LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsStudents photograph the bean daily and match the plant's growth to watering and daylight in the data. The logger runs on a USB charger for the whole experiment.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
Capacitive probe that measures soil moisture without exposed metal, so it does not corrode like resistive probes.
Light-dependent resistor with a comparator: its output flips when the light falls below the level set by the trimmer.
Temperature-compensated real-time clock (±2 minutes a year) with a coin-cell backup, so the time survives power cuts.
Stores readings on a microSD card as a CSV file you can open in Excel or Google Sheets.
Follow the colours: red is power, dark grey is ground, blue is a signal.
class_bean_growth_log.inoVerify & upload in Electrolark// Bean growth: soil and light log
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "class-bean-growth-log"
#include <Wire.h>
#include <RTClib.h>
#include <SPI.h>
#include <SD.h>
// ---- pins ----
const uint8_t SOIL_PIN = A0;
const uint8_t LDR_PIN = 2;
const uint8_t SD_CS = 10;
const int SOIL_DRY = 520; // reading in dry air: calibrate
const int SOIL_WET = 260; // reading in a glass of water: calibrate
RTC_DS3231 rtc;
// ---- latest readings ----
int soilPct = 0;
bool dark = false;
const unsigned long LOG_EVERY_MS = 900000UL; // one row per 900 s
unsigned long lastLog = 0;
bool cardOk = false;
void writeRow() {
File f = SD.open("LOG.CSV", FILE_WRITE);
if (!f) { Serial.println(F("Write failed")); return; }
DateTime t = rtc.now();
char stamp[20];
snprintf(stamp, sizeof(stamp), "%04d-%02d-%02d,%02d:%02d:%02d", t.year(), t.month(), t.day(), t.hour(), t.minute(), t.second());
f.print(stamp);
f.print(',');
f.print(soilPct);
f.print(',');
f.print(dark);
f.println();
f.close();
}
void setup() {
Serial.begin(115200);
pinMode(LDR_PIN, INPUT);
if (!rtc.begin()) Serial.println(F("RTC not found"));
if (rtc.lostPower()) rtc.adjust(DateTime(F(__DATE__), F(__TIME__))); // set from the upload time
cardOk = SD.begin(SD_CS);
Serial.println(cardOk ? F("SD card ready") : F("SD card not found"));
if (cardOk && !SD.exists("LOG.CSV")) {
File f = SD.open("LOG.CSV", FILE_WRITE);
if (f) { f.println(F("date,time,Soil(%),Dark")); f.close(); }
}
}
void loop() {
if (millis() - lastLog < LOG_EVERY_MS && lastLog != 0) return;
lastLog = millis();
soilPct = constrain(map(analogRead(SOIL_PIN), SOIL_DRY, SOIL_WET, 0, 100), 0, 100);
dark = digitalRead(LDR_PIN) == HIGH;
Serial.print(F("Soil="));
Serial.print(soilPct);
Serial.print(F("%"));
Serial.print(F(", Dark="));
Serial.print(dark ? F("yes") : F("no"));
Serial.println();
if (cardOk) writeRow();
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Calibrate: note the raw reading in dry air and in water, and put them in SOIL_DRY and SOIL_WET.
Some modules invert DO. Change == HIGH to == LOW in the code.
The coin cell is flat or missing. Some modules need the charging resistor removed when using a CR2032.
Check the card is FAT32, fully inserted, and CS is on the pin in the sketch.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Plot soil moisture against day; students mark when they watered.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider. Analog readings run 0–4095 instead of 0–1023, which the ADC_MAX constant handles.
Use a 5 V USB phone charger or a power bank into the board's USB port.
9 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, Capacitive Soil Moisture Sensor – 3.3V/5V Analog Output, Digital LDR Light Sensor Module – LM393, DS3231 Precision RTC Module with EEPROM, DFRobot Fermion MicroSD Card Module – SPI, microSD Memory Card Class 10 (16GB), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 2 weeks. The build on this page has 9 steps.
No. This page has the complete, tested code (class_bean_growth_log.ino). Install these libraries first: RTClib and SD.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹1,443 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Plant needs; Long experiments.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
%, Dark=no Soil=81%, Dark=no Soil=81%, Dark=no Soil=81%, Dark=no Soil=82%, Dark=no Soil=81%, Dark=no Soil=81%, Dark=no
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.