LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsSurface temperature changes with blood flow. Students read their forehead and palm at rest and after exercise and compare.
Not a medical device.
Not a medical device. Readings are for learning and must not be used for diagnosis.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
Infrared thermometer: measures the temperature of whatever it points at without touching it (field of view about 90°).
Follow the colours: red is power, dark grey is ground, blue is a signal.
class_body_temperature_exercise.inoVerify & upload in Electrolark// Skin temperature before and after exercise
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "class-body-temperature-exercise"
#include <Wire.h>
#include <Adafruit_MLX90614.h>
#include <Adafruit_GFX.h>
#include <Adafruit_SSD1306.h>
Adafruit_MLX90614 mlx;
Adafruit_SSD1306 oled(128, 64, &Wire, -1);
// ---- latest readings ----
float objC = 0;
float ambC = 0;
const unsigned long READ_EVERY_MS = 1000;
unsigned long lastRead = 0;
const char* statusText = "OK";
void updateDisplay() {
oled.clearDisplay();
oled.setTextSize(1);
oled.setCursor(0, 0);
oled.print(F("Skin"));
oled.drawLine(0, 10, 127, 10, SSD1306_WHITE);
oled.setCursor(0, 16);
oled.print(F("Object"));
oled.setTextSize(2);
oled.setCursor(0, 28);
oled.print(objC, 1);
oled.print(F(" C"));
oled.setTextSize(1);
oled.display();
}
void setup() {
Serial.begin(115200);
if (!mlx.begin()) Serial.println(F("MLX90614 not found"));
if (!oled.begin(SSD1306_SWITCHCAPVCC, 0x3C)) Serial.println(F("OLED not found"));
oled.setTextColor(SSD1306_WHITE);
oled.clearDisplay();
oled.display();
}
void loop() {
if (millis() - lastRead < READ_EVERY_MS) return;
lastRead = millis();
objC = mlx.readObjectTempC();
ambC = mlx.readAmbientTempC();
Serial.print(F("Object="));
Serial.print(objC, 1);
Serial.print(F("C"));
Serial.println();
updateDisplay();
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
You are too far away, so the sensor sees mostly background. Move closer.
Check SDA/SCL and try address 0x3D. Run an I²C scanner to confirm.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Not for medical use; each student measures their own.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
6 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, MLX90614 IR Non-Contact Temperature Sensor Module, 0.96" OLED Display 128x64 (I2C), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 45 minutes. The build on this page has 7 steps.
No. This page has the complete, tested code (class_body_temperature_exercise.ino). Install these libraries first: Adafruit MLX90614 Library, Adafruit SSD1306 and Adafruit GFX Library.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹1,188 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Thermoregulation; Infrared sensing.
Not a medical device. Not a medical device. Readings are for learning and must not be used for diagnosis.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Object=34.9C Object=35.0C
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.