LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsPut a little warm water in a plastic bottle, with the BMP280 inside on wires sealed through the cap with hot glue, with a bicycle-pump valve in the cap. Pump to raise the pressure, then release it suddenly: the pressure falls, the air cools by a degree or two, and a cloud appears. The LCD shows both changes.
Use a strong soft-drink bottle and pump only a few strokes. Wear safety glasses.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
Measures barometric pressure (±1 hPa) and temperature over I²C.
Classic 16-character, 2-line LCD with an I²C backpack, so it needs only two signal wires.
Follow the colours: red is power, dark grey is ground, blue is a signal.
class_cloud_in_a_bottle.inoVerify & upload in Electrolark// Make a cloud in a bottle
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "class-cloud-in-a-bottle"
#include <Wire.h>
#include <Adafruit_BMP280.h>
#include <LiquidCrystal_I2C.h>
Adafruit_BMP280 bmp;
LiquidCrystal_I2C lcd(0x27, 16, 2);
// ---- latest readings ----
float pressHpa = 0;
float bmpC = 0;
const unsigned long READ_EVERY_MS = 200;
unsigned long lastRead = 0;
const char* statusText = "OK";
void updateDisplay() {
lcd.setCursor(0, 0);
lcd.print(F("Pressure "));
lcd.print(pressHpa, 1);
lcd.print(F(" hPa"));
lcd.print(F(" "));
lcd.setCursor(0, 1);
lcd.print(F("Temp "));
lcd.print(bmpC, 1);
lcd.print(F(" C"));
lcd.print(F(" "));
}
void setup() {
Serial.begin(115200);
if (!bmp.begin(0x76) && !bmp.begin(0x77)) Serial.println(F("BMP280 not found"));
lcd.init();
lcd.backlight();
}
void loop() {
if (millis() - lastRead < READ_EVERY_MS) return;
lastRead = millis();
pressHpa = bmp.readPressure() / 100.0f;
bmpC = bmp.readTemperature();
Serial.print(F("Pressure="));
Serial.print(pressHpa, 1);
Serial.print(F("hPa"));
Serial.print(F(", Temp="));
Serial.print(bmpC, 1);
Serial.print(F("C"));
Serial.println();
updateDisplay();
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Check SDA/SCL are not swapped. Run an I²C scanner sketch to confirm the address.
Adjust the contrast pot on the backpack. If still blank, change 0x27 to 0x3F.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Add a lit match's smoke before sealing (teacher only) to give the droplets something to form on. Discuss why clouds form as air rises and expands.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
6 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, BMP280 Temperature & Barometric Pressure Sensor Module, LCD1602 16x2 Character LCD (blue, with I2C adapter), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 45 minutes. The build on this page has 7 steps.
No. This page has the complete, tested code (class_cloud_in_a_bottle.ino). Install these libraries first: Adafruit BMP280 Library and LiquidCrystal I2C.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹518 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Pressure and temperature; How clouds form.
Use a strong soft-drink bottle and pump only a few strokes. Wear safety glasses.
Ideas that reuse this build: Syringe air pressure and Barometer weather. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
hPa, Temp=25.9C Pressure=1008.1hPa, Temp=26.0C Pressure=1008.0hPa, Temp=26.1C Pressure=1008.0hPa, Temp=26.1C Pressure=1008.2hPa, Temp=26.0C Pressure=1008.0hPa, Temp=26.0C
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.