LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsThe DHT22 measures the room air and the sketch calculates the dew point. A probe taped to a metal can of water shows its temperature as you add ice. Water droplets appear on the can just as its temperature falls below the dew point.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
Measures air temperature (±0.5 °C) and relative humidity (±2–5 %) on a single data wire.; Calculates the dew point of the room air so the sketch can warn when the glass is colder than that.
Waterproof stainless-steel probe that reads liquid or soil temperature from −55 to +125 °C (±0.5 °C).
Follow the colours: red is power, dark grey is ground, blue is a signal.
class_dew_point_cold_can.inoVerify & upload in Electrolark// When does a cold can start to sweat?
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "class-dew-point-cold-can"
#include <DHT.h>
#include <OneWire.h>
#include <DallasTemperature.h>
#include <Wire.h>
#include <Adafruit_GFX.h>
#include <Adafruit_SSD1306.h>
// ---- pins ----
const uint8_t DHT_PIN = 2;
const uint8_t ONEWIRE_PIN = 3;
DHT dht(DHT_PIN, DHT22);
OneWire oneWire(ONEWIRE_PIN);
DallasTemperature probes(&oneWire);
Adafruit_SSD1306 oled(128, 64, &Wire, -1);
// ---- latest readings ----
float tempC = 0;
float humidity = 0;
float dewC = 0;
float margin = 0;
float probeC = 0;
const unsigned long READ_EVERY_MS = 1000;
unsigned long lastRead = 0;
const char* statusText = "OK";
float dewPointC(float t, float rh) {
float g = log(rh / 100.0f) + (17.62f * t) / (243.12f + t); // Magnus formula
return 243.12f * g / (17.62f - g);
}
float readProbeC() {
probes.requestTemperatures();
return probes.getTempCByIndex(0);
}
void updateDisplay() {
oled.clearDisplay();
oled.setTextSize(1);
oled.setCursor(0, 0);
oled.print(F("Dew point"));
oled.drawLine(0, 10, 127, 10, SSD1306_WHITE);
oled.setCursor(0, 14);
oled.print(F("Dew point: "));
oled.print(dewC, 1);
oled.print(F(" °C"));
oled.setCursor(0, 24);
oled.print(F("Probe: "));
oled.print(probeC, 1);
oled.print(F(" C"));
oled.setCursor(0, 56);
oled.print(statusText);
oled.display();
}
void setup() {
Serial.begin(115200);
dht.begin();
probes.begin();
if (!oled.begin(SSD1306_SWITCHCAPVCC, 0x3C)) Serial.println(F("OLED not found"));
oled.setTextColor(SSD1306_WHITE);
oled.clearDisplay();
oled.display();
}
void loop() {
if (millis() - lastRead < READ_EVERY_MS) return;
lastRead = millis();
tempC = dht.readTemperature();
humidity = dht.readHumidity();
dewC = dewPointC(tempC, humidity);
margin = probeC - dewC;
probeC = readProbeC();
statusText = (!isnan(tempC) && !isnan(humidity) && probeC > -100) ? "OK" : "Sensor error";
Serial.print(F("Dew point="));
Serial.print(dewC, 1);
Serial.print(F("°C"));
Serial.print(F(", Probe="));
Serial.print(probeC, 1);
Serial.print(F("C"));
Serial.println();
updateDisplay();
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Check the DATA wire and the pull-up. The DHT22 needs at least 2 seconds between reads, so do not poll it faster.
The 4.7 kΩ pull-up is missing or DATA is on the wrong pin. Check the yellow wire.
Check SDA/SCL and try address 0x3D. Run an I²C scanner to confirm.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Students record the can temperature when the first droplets appear and compare with the dew point on the screen. Try on a dry day and a humid one.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
8 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, DHT22 Temperature & Humidity Sensor, DS18B20 Waterproof Temperature Probe – 1m Cable, 0.96" OLED Display 128x64 (I2C), Resistor Assortment Kit (30 Values), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 1 hour. The build on this page has 8 steps.
No. This page has the complete, tested code (class_dew_point_cold_can.ino). Install these libraries first: DHT sensor library, Adafruit Unified Sensor, OneWire, DallasTemperature, Adafruit SSD1306 and Adafruit GFX Library.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹701 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Condensation; Humidity and dew point.
Ideas that reuse this build: Humidity of breath and Dew-point window alarm. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Dew point=17.0°C, Probe=26.0C Dew point=17.2°C, Probe=26.0C
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.