LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsWhen the room gets darker than the trimmer setting, the LED comes on. Students adjust the trimmer, cover the sensor and describe the cause-and-effect chain in a flow diagram.
Every main part of this project is an item on the public Package 1 equipment list, so a school lab that already owns Package 1 can build it without buying anything extra.
See the full Atal Tinkering Lab packages →
Geekobot is an independent shop, not endorsed by or affiliated with NITI Aayog or the Atal Innovation Mission. Item names follow the public AIM equipment list.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
Light-dependent resistor with a comparator: its output flips when the light falls below the level set by the trimmer.
Active buzzer with a built-in oscillator: apply power and it beeps at about 2.3 kHz.
Follow the colours: red is power, dark grey is ground, blue is a signal.
class_ldr_dark_detector.inoVerify & upload in Electrolark// Build a dark detector
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "class-ldr-dark-detector"
// ---- pins ----
const uint8_t LDR_PIN = 2;
const uint8_t LED_YELLOW = 3;
const uint8_t BUZZER_PIN = 4;
// ---- latest readings ----
bool dark = false;
const unsigned long READ_EVERY_MS = 50;
unsigned long lastRead = 0;
bool alertOn = false;
const char* statusText = "Starting";
const unsigned long HOLD_MS = 300; // stay on this long after the last trigger
unsigned long lastTrigger = 0;
void setYellowLed(bool on) { digitalWrite(LED_YELLOW, on ? HIGH : LOW); }
void setBuzzer(bool on) { digitalWrite(BUZZER_PIN, on ? HIGH : LOW); }
void evaluate() {
if (dark) lastTrigger = millis();
alertOn = lastTrigger != 0 && millis() - lastTrigger < HOLD_MS;
statusText = alertOn ? "DARK" : "OK";
}
void setup() {
Serial.begin(115200);
pinMode(LDR_PIN, INPUT);
pinMode(LED_YELLOW, OUTPUT);
pinMode(BUZZER_PIN, OUTPUT);
setBuzzer(false);
}
void loop() {
if (millis() - lastRead >= READ_EVERY_MS) {
lastRead = millis();
dark = digitalRead(LDR_PIN) == HIGH;
evaluate();
Serial.print(F("Dark="));
Serial.print(dark ? F("yes") : F("no"));
Serial.print(F(", status=")); Serial.println(statusText);
}
setYellowLed(alertOn);
setBuzzer(alertOn);
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Some modules invert DO. Change == HIGH to == LOW in the code.
LED is reversed; flip it. Check the 220 Ω resistor is in series.
Low-triggered module: invert the logic in setBuzzer().
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Have students draw input, process, output before wiring.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
8 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, Digital LDR Light Sensor Module – LM393, Through-Hole LED Pack (Pack of 10), Active Buzzer Module 3.3–5V, Resistor Assortment Kit (30 Values), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 30 minutes. The build on this page has 8 steps.
No. This page has the complete, tested code (class_ldr_dark_detector.ino).
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹428 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Input, process, output; Thresholds.
Ideas that reuse this build: LM358 version without code. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Dark=no, status=OK Dark=no, status=OK Dark=no, status=OK Dark=no, status=OK Dark=no, status=OK Dark=no, status=OK Dark=no, status=OK Dark=no, status=OK Dark=no, status=OK
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.