LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsPlace the sensor on the table pointing up at the bottom of a ruler that hangs just above it. A partner lets go; you catch it. The sensor sees how far the ruler fell before it stopped, and the sketch calculates t = √(2d/g) and shows it in milliseconds.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
Laser time-of-flight sensor: measures 3 cm to about 1.2 m with millimetre resolution in a tiny package.
Bright 4-digit 7-segment display driven by two wires.
Follow the colours: red is power, dark grey is ground, blue is a signal.
class_reaction_ruler.inoVerify & upload in Electrolark// Reaction time with a ruler and a sensor
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "class-reaction-ruler"
#include <Wire.h>
#include <Adafruit_VL53L0X.h>
#include <TM1637Display.h>
// ---- pins ----
const uint8_t SEG_CLK = 2;
const uint8_t SEG_DIO = 3;
Adafruit_VL53L0X tof;
TM1637Display seg(SEG_CLK, SEG_DIO);
// ---- latest readings ----
int tofMm = 0;
// The sensor sits on the table pointing up at the bottom end of a hanging ruler.
int restMm = 0;
int minMm = 0;
bool falling = false;
unsigned long lastMove = 0;
int readTofMm() {
VL53L0X_RangingMeasurementData_t m;
tof.rangingTest(&m, false);
return (m.RangeStatus != 4) ? m.RangeMilliMeter : -1;
}
void setup() {
Serial.begin(115200);
if (!tof.begin()) Serial.println(F("VL53L0X not found"));
seg.setBrightness(5);
seg.clear();
delay(500);
restMm = readTofMm();
Serial.print(F("Rest distance (mm): ")); Serial.println(restMm);
seg.showNumberDec(0);
}
void loop() {
int d = readTofMm();
if (d < 0) { delay(10); return; }
if (!falling) {
if (d < restMm - 8) { falling = true; minMm = d; lastMove = millis(); } // ruler released
else restMm = (restMm * 7 + d) / 8; // follow slow drift
} else {
if (d < minMm - 1) { minMm = d; lastMove = millis(); }
else if (millis() - lastMove > 200) { // ruler has stopped: it was caught
float fallM = (restMm - minMm) / 1000.0f;
float t = sqrt(2.0f * fallM / 9.81f); // t = sqrt(2d / g)
seg.showNumberDec((int)(t * 1000), false);
Serial.print(F("Fell ")); Serial.print((restMm - minMm)); Serial.print(F(" mm, reaction time ")); Serial.print(t * 1000, 0); Serial.println(F(" ms"));
delay(3000);
restMm = readTofMm();
falling = false;
}
}
delay(5);
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Target is out of range or too dark/shiny. Try a white card within 1 m.
CLK and DIO swapped; swap them.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Compare dominant and non-dominant hands, and before and after a distraction. A typical result is 150 to 250 ms, and the ruler falls 11 to 30 cm.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
6 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, VL53L0X ToF Laser Distance Sensor Module, TM1637 4-Digit 7-Segment Display Module, Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 1 hour. The build on this page has 7 steps.
No. This page has the complete, tested code (class_reaction_ruler.ino). Install these libraries first: Adafruit_VL53L0X and TM1637.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹489 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Free fall; Reaction time.
Ideas that reuse this build: Reaction timer game. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Rest distance (mm): 398
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.