LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsSound spreads out as it travels, so it gets weaker with distance. Students clap or play a tone at set distances and record the sensor reading; sound intensity follows an inverse-square law, so the amplitude the sensor reads falls roughly in proportion to 1/distance.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
Follow the colours: red is power, dark grey is ground, blue is a signal.
class_sound_vs_distance.inoVerify & upload in Electrolark// Does sound get quieter with distance?
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "class-sound-vs-distance"
#include <Wire.h>
#include <Adafruit_GFX.h>
#include <Adafruit_SSD1306.h>
// ---- pins ----
const uint8_t MIC_PIN = A0;
const int ADC_MAX = 1023; // 10-bit analog input
const float VREF = 5.0f;
Adafruit_SSD1306 oled(128, 64, &Wire, -1);
// ---- latest readings ----
int soundPct = 0;
const unsigned long READ_EVERY_MS = 100;
unsigned long lastRead = 0;
const char* statusText = "OK";
int readSoundLevel() {
// peak-to-peak amplitude over a 50 ms window
unsigned long start = millis();
int lo = ADC_MAX, hi = 0;
while (millis() - start < 50) {
int v = analogRead(MIC_PIN);
if (v < lo) lo = v;
if (v > hi) hi = v;
}
return (int)((hi - lo) * 100L / ADC_MAX);
}
void updateDisplay() {
oled.clearDisplay();
oled.setTextSize(1);
oled.setCursor(0, 0);
oled.print(F("Sound"));
oled.drawLine(0, 10, 127, 10, SSD1306_WHITE);
oled.setCursor(0, 16);
oled.print(F("Sound"));
oled.setTextSize(2);
oled.setCursor(0, 28);
oled.print(soundPct);
oled.print(F("%"));
oled.setTextSize(1);
oled.display();
}
void setup() {
Serial.begin(115200);
if (!oled.begin(SSD1306_SWITCHCAPVCC, 0x3C)) Serial.println(F("OLED not found"));
oled.setTextColor(SSD1306_WHITE);
oled.clearDisplay();
oled.display();
}
void loop() {
if (millis() - lastRead < READ_EVERY_MS) return;
lastRead = millis();
soundPct = readSoundLevel();
Serial.print(F("Sound="));
Serial.print(soundPct);
Serial.print(F("%"));
Serial.println();
updateDisplay();
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Turn the module trimmer to increase gain, or move the mic closer to the sound.
Check SDA/SCL and try address 0x3D. Run an I²C scanner to confirm.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Use a phone tone generator for repeatable loudness.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider. Analog readings run 0–4095 instead of 0–1023, which the ADC_MAX constant handles.
Use a 5 V USB phone charger or a power bank into the board's USB port.
6 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, Analog Sound Sensor Microphone Module, 0.96" OLED Display 128x64 (I2C), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 45 minutes. The build on this page has 7 steps.
No. This page has the complete, tested code (class_sound_vs_distance.ino). Install these libraries first: Adafruit SSD1306 and Adafruit GFX Library.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹593 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Inverse square law; Sound intensity.
Ideas that reuse this build: Noise meter. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Sound=9% Sound=9% Sound=10% Sound=9% Sound=9% Sound=9% Sound=9% Sound=9% Sound=9%
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.