LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsA good thermometer reads 0 °C in ice water and about 100 °C in boiling water (less at altitude). Students write a correction and see why calibration matters.
An adult handles boiling water.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
Waterproof stainless-steel probe that reads liquid or soil temperature from −55 to +125 °C (±0.5 °C).
Bright 4-digit 7-segment display driven by two wires.
Follow the colours: red is power, dark grey is ground, blue is a signal.
class_thermometer_calibration.inoVerify & upload in Electrolark// Calibrate a thermometer
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "class-thermometer-calibration"
#include <OneWire.h>
#include <DallasTemperature.h>
#include <TM1637Display.h>
// ---- pins ----
const uint8_t ONEWIRE_PIN = 2;
const uint8_t SEG_CLK = 3;
const uint8_t SEG_DIO = 4;
OneWire oneWire(ONEWIRE_PIN);
DallasTemperature probes(&oneWire);
TM1637Display seg(SEG_CLK, SEG_DIO);
// ---- latest readings ----
float probeC = 0;
const unsigned long READ_EVERY_MS = 300;
unsigned long lastRead = 0;
const char* statusText = "OK";
float readProbeC() {
probes.requestTemperatures();
return probes.getTempCByIndex(0);
}
void updateDisplay() {
{ float segV = probeC; // shows 0.00 to 9.99, then 10.0 to 99.9, with a decimal point
if (segV < 0) seg.showNumberDec((int)round(segV), false);
else {
segV = min(segV, 99.9f);
int n = segV < 10 ? (int)round(segV * 100) : (int)round(segV * 10);
uint8_t s[4] = {seg.encodeDigit(n / 100 % 10), seg.encodeDigit(n / 10 % 10), seg.encodeDigit(n % 10), 0};
s[segV < 10 ? 0 : 1] |= 0x80; // decimal point
seg.setSegments(s);
}
}
}
void setup() {
Serial.begin(115200);
probes.begin();
seg.setBrightness(5);
seg.clear();
}
void loop() {
if (millis() - lastRead < READ_EVERY_MS) return;
lastRead = millis();
probeC = readProbeC();
statusText = (probeC > -100) ? "OK" : "Sensor error";
Serial.print(F("Probe="));
Serial.print(probeC, 1);
Serial.print(F("C"));
Serial.println();
updateDisplay();
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
The 4.7 kΩ pull-up is missing or DATA is on the wrong pin. Check the yellow wire.
CLK and DIO swapped; swap them.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
An adult handles the hot water.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
7 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, DS18B20 Waterproof Temperature Probe – 1m Cable, TM1637 4-Digit 7-Segment Display Module, Resistor Assortment Kit (30 Values), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 1 hour. The build on this page has 7 steps.
No. This page has the complete, tested code (class_thermometer_calibration.ino). Install these libraries first: OneWire, DallasTemperature and TM1637.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹460 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Calibration; Accuracy.
An adult handles boiling water.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Probe=26.0C Probe=26.0C Probe=26.0C Probe=26.0C Probe=26.0C Probe=26.0C Probe=26.0C Probe=26.0C
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.