LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsPure water barely conducts; salty water conducts well. The rain-board dipped in a beaker reads higher with each added spoon of salt, and students graph the relationship.
Every main part of this project is an item on the public Package 1 equipment list, so a school lab that already owns Package 1 can build it without buying anything extra.
See the full Atal Tinkering Lab packages →
Geekobot is an independent shop, not endorsed by or affiliated with NITI Aayog or the Atal Innovation Mission. Item names follow the public AIM equipment list.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
Comb-patterned plate whose resistance drops when water bridges the tracks.
Bright 4-digit 7-segment display driven by two wires.
Follow the colours: red is power, dark grey is ground, blue is a signal.
class_water_electrolysis_sensor.inoVerify & upload in Electrolark// Salt in the water: conductivity test
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "class-water-electrolysis-sensor"
#include <TM1637Display.h>
// ---- pins ----
const uint8_t RAIN_PIN = A0;
const uint8_t SEG_CLK = 2;
const uint8_t SEG_DIO = 3;
const int ADC_MAX = 1023; // 10-bit analog input
const float VREF = 5.0f;
TM1637Display seg(SEG_CLK, SEG_DIO);
// ---- latest readings ----
int wetPct = 0;
const unsigned long READ_EVERY_MS = 300;
unsigned long lastRead = 0;
const char* statusText = "OK";
void updateDisplay() {
seg.showNumberDec((int)round(wetPct), false);
}
void setup() {
Serial.begin(115200);
seg.setBrightness(5);
seg.clear();
}
void loop() {
if (millis() - lastRead < READ_EVERY_MS) return;
lastRead = millis();
wetPct = (int)(100 - analogRead(RAIN_PIN) * 100L / ADC_MAX);
Serial.print(F("Rain="));
Serial.print(wetPct);
Serial.print(F("%"));
Serial.println();
updateDisplay();
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Dry the plate and clean off residue. Powering it only when reading slows corrosion.
CLK and DIO swapped; swap them.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Use distilled water if available; rinse and dry the board between tests.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider. Analog readings run 0–4095 instead of 0–1023, which the ADC_MAX constant handles.
Use a 5 V USB phone charger or a power bank into the board's USB port.
6 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, HS-S09-PB Rain Sensor Kit – Analog/Digital Output, TM1637 4-Digit 7-Segment Display Module, Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 45 minutes. The build on this page has 7 steps.
No. This page has the complete, tested code (class_water_electrolysis_sensor.ino). Install this library first: TM1637.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹596 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Ions and conductivity; Dose-response.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Rain=71% Rain=71% Rain=70% Rain=70% Rain=70% Rain=71% Rain=70% Rain=70%
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.