LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsLights and fans left on in empty classrooms are a big part of a school's power bill. A light sensor sees whether the room is lit and a PIR sees whether anyone is there. If it is lit and empty for 30 minutes, the buzzer chirps in the corridor so the next person switches it off.
Every main part of this project is an item on the public Package 1 equipment list, so a school lab that already owns Package 1 can build it without buying anything extra.
See the full Atal Tinkering Lab packages →
Geekobot is an independent shop, not endorsed by or affiliated with NITI Aayog or the Atal Innovation Mission. Item names follow the public AIM equipment list.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Tells the board whether the room light is on: the comparator output goes LOW in bright light.
Passive infrared sensor that detects the body heat of moving people or animals up to about 7 m away.
Active buzzer with a built-in oscillator: apply power and it beeps at about 2.3 kHz.
Follow the colours: red is power, dark grey is ground, blue is a signal.
classroom_lights_left_on_alarm.inoVerify & upload in Electrolark// Classroom lights left on alarm
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "classroom-lights-left-on-alarm"
// ---- pins ----
const uint8_t LDR_PIN = 2;
const uint8_t PIR_PIN = 3;
const uint8_t BUZZER_PIN = 4;
const uint8_t LED_RED = 5;
// ---- latest readings ----
bool light = false;
bool motion = false;
const unsigned long AWAY_MS = 30 * 60000UL; // Light on with nobody around for this long
unsigned long lastPerson = 0;
bool alarm = false;
void setBuzzer(bool on) { digitalWrite(BUZZER_PIN, on ? HIGH : LOW); }
void setRedLed(bool on) { digitalWrite(LED_RED, on ? HIGH : LOW); }
void setup() {
Serial.begin(115200);
pinMode(LDR_PIN, INPUT);
pinMode(PIR_PIN, INPUT);
pinMode(BUZZER_PIN, OUTPUT);
setBuzzer(false);
pinMode(LED_RED, OUTPUT);
lastPerson = millis();
setBuzzer(false);
}
void loop() {
light = digitalRead(LDR_PIN) == LOW;
motion = digitalRead(PIR_PIN) == HIGH;
if (motion) lastPerson = millis();
alarm = light && millis() - lastPerson > AWAY_MS;
setRedLed(light);
setBuzzer(alarm && (millis() / 300) % 2 == 0);
static unsigned long lastLog = 0;
if (millis() - lastLog > 2000) {
lastLog = millis();
Serial.print(light ? F("Light ON, ") : F("Light off, ")); Serial.print((millis() - lastPerson) / 1000); Serial.println(F(" s since someone was seen"));
}
delay(20);
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Some modules invert DO. Change == HIGH to == LOW in the code.
Give it a minute to settle after power-up and keep it away from heaters, windows and fans.
Turn the sensitivity (Sx) pot clockwise and check the module has 5 V on VCC.
Low-triggered module: invert the logic in setBuzzer().
LED is reversed; flip it. Check the 220 Ω resistor is in series.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
8 parts: Nano CH340 Development Board (Soldered), Digital LDR Light Sensor Module – LM393, HC-SR501 PIR Motion Detector Sensor Module, Active Buzzer Module 3.3–5V, Through-Hole LED Pack (Pack of 10), Resistor Assortment Kit (30 Values), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1–2 hours. The build on this page has 10 steps.
No. This page has the complete, tested code (classroom_lights_left_on_alarm.ino).
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹420 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Active vs passive buzzers; Current-limiting resistors for LEDs; Digital inputs and sensor hold time; Thresholds set in hardware vs software.
Ideas that reuse this build: Study lamp auto-off and Room light left-on alarm. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Light ON, 2 s since someone was seen
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.