Remote-controlled RGB mood light
Warm, cool, rainbow or breathing: cycle lighting moods from your sofa.
Shop by category
Shop all componentsModelled on how polling machines work. Each voter presses one candidate button; the machine beeps, shows "Vote recorded" and locks for a moment so one person cannot vote twice in a row. Counts are stored in memory that survives power cuts. Only the teacher, holding buttons 1 and 3 together for three seconds, can see the totals. Hold button 2 while switching on to clear the count for a new election.
A classroom model only, not a real voting machine.
Every main part of this project is an item on the public Package 1 equipment list, so a school lab that already owns Package 1 can build it without buying anything extra.
See the full Atal Tinkering Lab packages →
Geekobot is an independent shop, not endorsed by or affiliated with NITI Aayog or the Atal Innovation Mission. Item names follow the public AIM equipment list.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Three momentary buttons, one leg each to a pin and the other legs joined to GND; the internal pull-ups do the rest.
Classic 16-character, 2-line LCD with an I²C backpack, so it needs only two signal wires.
Active buzzer with a built-in oscillator: apply power and it beeps at about 2.3 kHz.
Follow the colours: red is power, dark grey is ground, blue is a signal.
classroom_voting_machine_model.inoVerify & upload in Electrolark// Classroom electronic voting machine model
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "classroom-voting-machine-model"
#include <Wire.h>
#include <LiquidCrystal_I2C.h>
#include <EEPROM.h>
// ---- pins ----
const uint8_t BTN_1 = 2;
const uint8_t BTN_2 = 3;
const uint8_t BTN_3 = 4;
const uint8_t BUZZER_PIN = 5;
LiquidCrystal_I2C lcd(0x27, 16, 2);
int votes[3] = {0, 0, 0}; // kept in EEPROM so a power cut does not lose the count
const char* NAMES[3] = {"Candidate A", "Candidate B", "Candidate C"};
// returns 0 when nothing is pressed, else 1-3
int pressedButton() {
if (digitalRead(BTN_1) == LOW) return 1;
if (digitalRead(BTN_2) == LOW) return 2;
if (digitalRead(BTN_3) == LOW) return 3;
return 0;
}
void setBuzzer(bool on) { digitalWrite(BUZZER_PIN, on ? HIGH : LOW); }
void showResults() {
lcd.clear(); lcd.print(F("A")); lcd.print(votes[0]); lcd.print(F(" B")); lcd.print(votes[1]); lcd.print(F(" C")); lcd.print(votes[2]);
lcd.setCursor(0, 1); lcd.print(F("Total ")); lcd.print(votes[0] + votes[1] + votes[2]);
delay(5000);
lcd.clear(); lcd.print(F("Press to vote"));
}
void setup() {
Serial.begin(115200);
pinMode(BTN_1, INPUT_PULLUP); pinMode(BTN_2, INPUT_PULLUP); pinMode(BTN_3, INPUT_PULLUP);
lcd.init();
lcd.backlight();
pinMode(BUZZER_PIN, OUTPUT);
setBuzzer(false);
EEPROM.get(0, votes);
for (int i = 0; i < 3; i++) if (votes[i] < 0 || votes[i] > 9999) votes[i] = 0;
if (digitalRead(BTN_2) == LOW) { votes[0] = votes[1] = votes[2] = 0; EEPROM.put(0, votes); lcd.print(F("Count cleared")); delay(1500); lcd.clear(); } // hold button 2 while powering on to start a new election
lcd.print(F("Press to vote"));
}
void loop() {
// results: hold buttons 1 and 3 together for 3 seconds (the teacher's secret)
if (digitalRead(BTN_1) == LOW && digitalRead(BTN_3) == LOW) {
unsigned long t = millis();
while (digitalRead(BTN_1) == LOW && digitalRead(BTN_3) == LOW) { if (millis() - t > 3000) { showResults(); return; } delay(10); }
return;
}
int p = pressedButton();
if (!p) return;
delay(80);
if (digitalRead(BTN_1) == LOW && digitalRead(BTN_3) == LOW) return; // it was the results combination
votes[p - 1]++;
EEPROM.put(0, votes);
lcd.clear(); lcd.print(F("Vote recorded")); lcd.setCursor(0, 1); lcd.print(F("Thank you!"));
setBuzzer(true); delay(400); setBuzzer(false);
Serial.print(F("Vote for ")); Serial.println(NAMES[p - 1]);
while (pressedButton()) delay(10);
delay(1500); // short lock-out so each voter votes once
lcd.clear(); lcd.print(F("Press to vote"));
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
It is rotated 90°; turn it so the legs span the gap.
Adjust the contrast pot on the backpack. If still blank, change 0x27 to 0x3F.
Low-triggered module: invert the logic in setBuzzer().
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
6 parts: Nano CH340 Development Board (Soldered), 3 × Tactile Push Button Switch, LCD1602 16x2 Character LCD (blue, with I2C adapter), Active Buzzer Module 3.3–5V, Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1–2 hours. The build on this page has 9 steps.
No. This page has the complete, tested code (classroom_voting_machine_model.ino). Install this library first: LiquidCrystal I2C.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹409 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Active vs passive buzzers; Character displays and I²C backpacks; Pull-ups and debouncing.
A classroom model only, not a real voting machine.
Ideas that reuse this build: Quiz buzzer and Two-team scoreboard. They are listed under Take it further on this page.
Warm, cool, rainbow or breathing: cycle lighting moods from your sofa.
Press to roll: the pips tumble and slow down before landing on a number.
Wait for the light, hit the button: how many milliseconds can you beat?
A bright 4-digit clock that keeps time through power cuts.
Learning project. Check every circuit and the datasheet of each part before you power it up.
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.