Remote-controlled RGB mood light
Warm, cool, rainbow or breathing: cycle lighting moods from your sofa.
Shop by category
Shop all componentsA queue display for a small clinic, pharmacy or bakery counter. Each press of the button shows the next number with a double beep; the number survives power cuts. Hold the button for three seconds at closing time to start again from zero.
Every main part of this project is an item on the public Package 1 equipment list, so a school lab that already owns Package 1 can build it without buying anything extra.
See the full Atal Tinkering Lab packages →
Geekobot is an independent shop, not endorsed by or affiliated with NITI Aayog or the Atal Innovation Mission. Item names follow the public AIM equipment list.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Bright 4-digit 7-segment display driven by two wires.
Active buzzer with a built-in oscillator: apply power and it beeps at about 2.3 kHz.
Follow the colours: red is power, dark grey is ground, blue is a signal.
clinic_token_display.inoVerify & upload in Electrolark// Clinic and shop token number display
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "clinic-token-display"
#include <TM1637Display.h>
#include <EEPROM.h>
// ---- pins ----
const uint8_t BUTTON_PIN = 2;
const uint8_t SEG_CLK = 3;
const uint8_t SEG_DIO = 4;
const uint8_t BUZZER_PIN = 5;
TM1637Display seg(SEG_CLK, SEG_DIO);
int token = 0; // kept in EEPROM so a power cut does not reset the queue
void setBuzzer(bool on) { digitalWrite(BUZZER_PIN, on ? HIGH : LOW); }
void setup() {
Serial.begin(115200);
pinMode(BUTTON_PIN, INPUT_PULLUP);
seg.setBrightness(5);
seg.clear();
pinMode(BUZZER_PIN, OUTPUT);
setBuzzer(false);
EEPROM.get(0, token);
if (token < 0 || token > 9999) token = 0;
seg.showNumberDec(token);
}
void loop() {
if (digitalRead(BUTTON_PIN) == LOW) {
unsigned long t = millis();
while (digitalRead(BUTTON_PIN) == LOW) delay(10);
if (millis() - t > 3000) token = 0; // hold 3 s at the end of the day to start again from 0
else token = (token + 1) % 10000; // a short press calls the next token
seg.showNumberDec(token);
EEPROM.put(0, token);
for (int i = 0; i < 2; i++) { setBuzzer(true); delay(120); setBuzzer(false); delay(120); }
Serial.print(F("Token ")); Serial.println(token);
}
delay(20);
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
The button is rotated 90°; legs on the same side are already connected. Turn it.
CLK and DIO swapped; swap them.
Low-triggered module: invert the logic in setBuzzer().
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
6 parts: Nano CH340 Development Board (Soldered), Tactile Push Button Switch, TM1637 4-Digit 7-Segment Display Module, Active Buzzer Module 3.3–5V, Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1 hour. The build on this page has 9 steps.
No. This page has the complete, tested code (clinic_token_display.ino). Install this library first: TM1637.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹341 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Active vs passive buzzers; Multiplexed 7-segment displays; Pull-ups and debouncing.
Ideas that reuse this build: Quiz buzzer and Visitor counter. They are listed under Take it further on this page.
Warm, cool, rainbow or breathing: cycle lighting moods from your sofa.
Press to roll: the pips tumble and slow down before landing on a number.
Wait for the light, hit the button: how many milliseconds can you beat?
A bright 4-digit clock that keeps time through power cuts.
Learning project. Check every circuit and the datasheet of each part before you power it up.
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.