LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsA slotted disc on the end of the drum shaft gives a pulse for each slot. The OLED shows the speed so the operator can set the dial to the same figure every shift and keep the packing rate steady.
Keep hands and loose clothing clear of belts and drums.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
A U-shaped infrared gate: every time a slot in a disc passes through it, the output pulses, so counting pulses gives the speed of a shaft.
Follow the colours: red is power, dark grey is ground, blue is a signal.
conveyor_belt_speed_meter.inoVerify & upload in Electrolark// Conveyor belt speed meter
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "conveyor-belt-speed-meter"
#include <Wire.h>
#include <Adafruit_GFX.h>
#include <Adafruit_SSD1306.h>
// ---- pins ----
const uint8_t SLOT_PIN = 2;
#ifndef IRAM_SAFE
#define IRAM_SAFE // only needed on ESP32 boards
#endif
volatile unsigned long slotPulses = 0;
unsigned long lastSlotMs = 0;
const int SLOTS_PER_TURN = 20; // holes in the disc on the shaft
Adafruit_SSD1306 oled(128, 64, &Wire, -1);
// ---- latest readings ----
float rpm = 0;
const unsigned long READ_EVERY_MS = 1000;
unsigned long lastRead = 0;
const char* statusText = "OK";
void IRAM_SAFE onSlotPulse() { slotPulses++; }
float readRpm() {
unsigned long now = millis();
float secs = (now - lastSlotMs) / 1000.0f;
if (secs <= 0) return 0;
noInterrupts();
unsigned long p = slotPulses;
slotPulses = 0;
interrupts();
lastSlotMs = now;
return (p / secs) * 60.0f / SLOTS_PER_TURN; // turns per minute
}
void updateDisplay() {
oled.clearDisplay();
oled.setTextSize(1);
oled.setCursor(0, 0);
oled.print(F("Belt drum"));
oled.drawLine(0, 10, 127, 10, SSD1306_WHITE);
oled.setCursor(0, 16);
oled.print(F("Speed"));
oled.setTextSize(2);
oled.setCursor(0, 28);
oled.print(rpm, 0);
oled.print(F(" rpm"));
oled.setTextSize(1);
oled.display();
}
void setup() {
Serial.begin(115200);
pinMode(SLOT_PIN, INPUT);
attachInterrupt(digitalPinToInterrupt(SLOT_PIN), onSlotPulse, RISING);
lastSlotMs = millis();
if (!oled.begin(SSD1306_SWITCHCAPVCC, 0x3C)) Serial.println(F("OLED not found"));
oled.setTextColor(SSD1306_WHITE);
oled.clearDisplay();
oled.display();
}
void loop() {
if (millis() - lastRead < READ_EVERY_MS) return;
lastRead = millis();
rpm = readRpm();
Serial.print(F("Speed="));
Serial.print(rpm, 0);
Serial.print(F("rpm"));
Serial.println();
updateDisplay();
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Check the disc passes through the gap and that the signal wire is on an interrupt pin (D2 or D3 on a Nano).
Count the slots again and set SLOTS_PER_TURN to the right number.
Check SDA/SCL and try address 0x3D. Run an I²C scanner to confirm.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
5 parts: Nano CH340 Development Board (Soldered), Groove Coupler Speed Measuring Sensor Module, 0.96" OLED Display 128x64 (I2C), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1 hour. The build on this page has 8 steps.
No. This page has the complete, tested code (conveyor_belt_speed_meter.ino). Install these libraries first: Adafruit SSD1306 and Adafruit GFX Library.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹464 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Counting pulses with interrupts; Drawing text on an I²C display.
Keep hands and loose clothing clear of belts and drums.
Ideas that reuse this build: DIY tachometer and Conveyor item present light. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Speed=0rpm Speed=0rpm
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.