LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsMany cities ration water in summer, and tankers are expensive. The flow sensor on the outlet of the overhead tank counts every litre; the display shows today's total and the buzzer chirps if water keeps running after the daily budget is used. Press the button each morning to start a new day. The total survives power cuts.
Every main part of this project is an item on the public Package 1 equipment list, so a school lab that already owns Package 1 can build it without buying anything extra.
See the full Atal Tinkering Lab packages →
Geekobot is an independent shop, not endorsed by or affiliated with NITI Aayog or the Atal Innovation Mission. Item names follow the public AIM equipment list.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
A small turbine with a magnet and Hall sensor: each turn sends a pulse, and pulses per second give the flow rate.
Bright 4-digit 7-segment display driven by two wires.
Active buzzer with a built-in oscillator: apply power and it beeps at about 2.3 kHz.
Follow the colours: red is power, dark grey is ground, blue is a signal.
daily_water_budget_meter.inoVerify & upload in Electrolark// Daily water budget meter
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "daily-water-budget-meter"
#include <TM1637Display.h>
#include <EEPROM.h>
#if defined(ESP32) || defined(ESP8266)
#define IRAM_SAFE IRAM_ATTR
#else
#define IRAM_SAFE
#endif
// ---- pins ----
const uint8_t FLOW_PIN = 2;
const uint8_t SEG_CLK = 3;
const uint8_t SEG_DIO = 4;
const uint8_t BUZZER_PIN = 5;
const uint8_t BUTTON_PIN = 6;
volatile unsigned long flowPulses = 0;
unsigned long lastFlowMs = 0;
float litresTotal = 0;
TM1637Display seg(SEG_CLK, SEG_DIO);
// ---- latest readings ----
float flowLpm = 0;
float litres = 0;
const float DAILY_LITRES = 500; // household budget per day: change to suit
float todayL = 0, savedLitres = 0; // savedLitres = today's total before the last power-up
unsigned long lastRead = 0, lastSave = 0;
void IRAM_SAFE onFlowPulse() { flowPulses++; }
float readFlowLpm() {
unsigned long now = millis();
float secs = (now - lastFlowMs) / 1000.0f;
if (secs <= 0) return 0;
noInterrupts();
unsigned long p = flowPulses;
flowPulses = 0;
interrupts();
lastFlowMs = now;
float lpm = (p / secs) / 7.5f; // YF-S201: about 7.5 pulses per second per L/min
litresTotal += lpm * secs / 60.0f;
return lpm;
}
void setBuzzer(bool on) { digitalWrite(BUZZER_PIN, on ? HIGH : LOW); }
void setup() {
Serial.begin(115200);
pinMode(FLOW_PIN, INPUT_PULLUP);
attachInterrupt(digitalPinToInterrupt(FLOW_PIN), onFlowPulse, RISING);
lastFlowMs = millis();
seg.setBrightness(5);
seg.clear();
pinMode(BUZZER_PIN, OUTPUT);
setBuzzer(false);
pinMode(BUTTON_PIN, INPUT_PULLUP);
EEPROM.get(0, savedLitres);
if (isnan(savedLitres) || savedLitres < 0 || savedLitres > 100000) savedLitres = 0;
}
void loop() {
if (digitalRead(BUTTON_PIN) == LOW) { savedLitres = 0; litresTotal = 0; todayL = 0; EEPROM.put(0, todayL); Serial.println(F("New day")); while (digitalRead(BUTTON_PIN) == LOW) delay(10); }
if (millis() - lastRead < 1000) return;
lastRead = millis();
flowLpm = readFlowLpm(); // also adds this second's water to litresTotal
todayL = savedLitres + litresTotal;
seg.showNumberDec((int)min(todayL, 9999.0f));
bool over = todayL > DAILY_LITRES;
setBuzzer(over && flowLpm > 0.2f && (millis() / 1000) % 4 == 0); // chirp while water still runs over budget
if (millis() - lastSave > 60000) { lastSave = millis(); EEPROM.put(0, todayL); } // survive power cuts
Serial.print(flowLpm, 2); Serial.print(F(" L/min, today ")); Serial.print(todayL, 1); Serial.println(F(" L"));
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Check the arrow direction and that the signal wire is on an interrupt-capable pin.
CLK and DIO swapped; swap them.
Low-triggered module: invert the logic in setBuzzer().
The button is rotated 90°; legs on the same side are already connected. Turn it.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
7 parts: Nano CH340 Development Board (Soldered), YF-S201 Water Flow Sensor 1–30 L/min, TM1637 4-Digit 7-Segment Display Module, Active Buzzer Module 3.3–5V, Tactile Push Button Switch, Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 2 hours. The build on this page has 11 steps.
No. This page has the complete, tested code (daily_water_budget_meter.ino). Install this library first: TM1637.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹528 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Active vs passive buzzers; Interrupts and counting pulses; Multiplexed 7-segment displays; Pull-ups and debouncing.
Ideas that reuse this build: Water flow meter and Water usage logger. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
0.00 L/min, today 0.0 L 0.00 L/min, today 0.0 L
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.