LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsEach turn of the turbine inside the YF-S201 sends a pulse. The Uno counts pulses with an interrupt, works out the flow rate every second and keeps a running total.
Every main part of this project is an item on the public Package 1 equipment list, so a school lab that already owns Package 1 can build it without buying anything extra.
See the full Atal Tinkering Lab packages →
Geekobot is an independent shop, not endorsed by or affiliated with NITI Aayog or the Atal Innovation Mission. Item names follow the public AIM equipment list.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
A small turbine with a magnet and Hall sensor: each turn sends a pulse, and pulses per second give the flow rate.
Classic 16-character, 2-line LCD with an I²C backpack, so it needs only two signal wires.
Follow the colours: red is power, dark grey is ground, blue is a signal.
water_flow_meter.inoVerify & upload in Electrolark// Water flow meter
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "water-flow-meter"
#include <Wire.h>
#include <LiquidCrystal_I2C.h>
#if defined(ESP32) || defined(ESP8266)
#define IRAM_SAFE IRAM_ATTR
#else
#define IRAM_SAFE
#endif
// ---- pins ----
const uint8_t FLOW_PIN = 2;
volatile unsigned long flowPulses = 0;
unsigned long lastFlowMs = 0;
float litresTotal = 0;
LiquidCrystal_I2C lcd(0x27, 16, 2);
// ---- latest readings ----
float flowLpm = 0;
float litres = 0;
const unsigned long READ_EVERY_MS = 1000;
unsigned long lastRead = 0;
const char* statusText = "OK";
void IRAM_SAFE onFlowPulse() { flowPulses++; }
float readFlowLpm() {
unsigned long now = millis();
float secs = (now - lastFlowMs) / 1000.0f;
if (secs <= 0) return 0;
noInterrupts();
unsigned long p = flowPulses;
flowPulses = 0;
interrupts();
lastFlowMs = now;
float lpm = (p / secs) / 7.5f; // YF-S201: about 7.5 pulses per second per L/min
litresTotal += lpm * secs / 60.0f;
return lpm;
}
void updateDisplay() {
lcd.setCursor(0, 0);
lcd.print(F("Flow "));
lcd.print(flowLpm, 1);
lcd.print(F(" L/min"));
lcd.print(F(" "));
lcd.setCursor(0, 1);
lcd.print(F("Total "));
lcd.print(litres, 2);
lcd.print(F(" L"));
lcd.print(F(" "));
}
void setup() {
Serial.begin(115200);
pinMode(FLOW_PIN, INPUT_PULLUP);
attachInterrupt(digitalPinToInterrupt(FLOW_PIN), onFlowPulse, RISING);
lastFlowMs = millis();
lcd.init();
lcd.backlight();
}
void loop() {
if (millis() - lastRead < READ_EVERY_MS) return;
lastRead = millis();
flowLpm = readFlowLpm();
litres = litresTotal;
Serial.print(F("Flow="));
Serial.print(flowLpm, 1);
Serial.print(F("L/min"));
Serial.print(F(", Total="));
Serial.print(litres, 2);
Serial.print(F("L"));
Serial.println();
updateDisplay();
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Check the arrow direction and that the signal wire is on an interrupt-capable pin.
Adjust the contrast pot on the backpack. If still blank, change 0x27 to 0x3F.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
6 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, YF-S201 Water Flow Sensor 1–30 L/min, LCD1602 16x2 Character LCD (blue, with I2C adapter), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 1–2 hours. The build on this page has 7 steps.
No. This page has the complete, tested code (water_flow_meter.ino). Install this library first: LiquidCrystal I2C.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹618 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Character displays and I²C backpacks; Interrupts and counting pulses.
Ideas that reuse this build: Wi-Fi version. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Flow=0.0L/min, Total=0.00L Flow=0.0L/min, Total=0.00L
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.