LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsA 12 V pump pulls a steady current while it pushes water, and much less when it runs dry or the pipe is blocked. The ACS712 measures the current on the pump's supply wire and the buzzer sounds when it falls below 0.4 A while the pump is meant to be running.
Use it only on 12 V DC pumps and battery circuits. Never put the ACS712 module on mains wiring.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Measures the current flowing through its two screw terminals with a Hall sensor, so the measured circuit stays electrically separate from the board.
Active buzzer with a built-in oscillator: apply power and it beeps at about 2.3 kHz.
Follow the colours: red is power, dark grey is ground, blue is a signal.
dc_pump_idle_current_alarm.inoVerify & upload in Electrolark// 12 V pump idle or dry-run current alarm
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "dc-pump-idle-current-alarm"
#include <Wire.h>
#include <Adafruit_GFX.h>
#include <Adafruit_SSD1306.h>
// ---- pins ----
const uint8_t CURRENT_PIN = A0;
const uint8_t BUZZER_PIN = 2;
const uint8_t LED_RED = 3;
const int ADC_MAX = 1023; // 10-bit analog input
const float VREF = 5.0f;
const float ACS_MV_PER_A = 185.0; // 5 A module: 185 mV per amp (20 A: 100, 30 A: 66)
float acsZero = 0; // output with no current, measured at start-up
Adafruit_SSD1306 oled(128, 64, &Wire, -1);
// ---- latest readings ----
float currentA = 0;
const unsigned long READ_EVERY_MS = 200;
unsigned long lastRead = 0;
bool alertOn = false;
const char* statusText = "Starting";
const float ALERT_LEVEL = 0.4; // read the current with water flowing and set the limit about half of that
const float HYSTERESIS = 0.15; // gap that stops rapid on/off switching
float readCurrentA() {
long s = 0;
for (int i = 0; i < 100; i++) s += analogRead(CURRENT_PIN); // average out the noise
float mv = (s / 100.0f - acsZero) * VREF * 1000.0f / ADC_MAX;
float a = mv / ACS_MV_PER_A;
return fabs(a) < 0.05f ? 0 : a;
}
void setBuzzer(bool on) { digitalWrite(BUZZER_PIN, on ? HIGH : LOW); }
void setRedLed(bool on) { digitalWrite(LED_RED, on ? HIGH : LOW); }
void updateDisplay() {
oled.clearDisplay();
oled.setTextSize(1);
oled.setCursor(0, 0);
oled.print(F("Pump current"));
oled.drawLine(0, 10, 127, 10, SSD1306_WHITE);
oled.setCursor(0, 16);
oled.print(F("Current"));
oled.setTextSize(2);
oled.setCursor(0, 28);
oled.print(currentA, 2);
oled.print(F(" A"));
oled.setTextSize(1);
oled.setCursor(0, 56);
oled.print(statusText);
oled.display();
}
void evaluate() {
if (!alertOn && currentA < ALERT_LEVEL) alertOn = true;
else if (alertOn && currentA > ALERT_LEVEL + HYSTERESIS) alertOn = false;
statusText = alertOn ? "PUMP DRY OR OFF" : "Pump loaded";
}
void setup() {
Serial.begin(115200);
{ long s = 0; for (int i = 0; i < 200; i++) { s += analogRead(CURRENT_PIN); delay(1); } acsZero = s / 200.0f; } // switch the load off while the board starts
if (!oled.begin(SSD1306_SWITCHCAPVCC, 0x3C)) Serial.println(F("OLED not found"));
oled.setTextColor(SSD1306_WHITE);
oled.clearDisplay();
oled.display();
pinMode(BUZZER_PIN, OUTPUT);
setBuzzer(false);
pinMode(LED_RED, OUTPUT);
}
void loop() {
if (millis() - lastRead >= READ_EVERY_MS) {
lastRead = millis();
currentA = readCurrentA();
evaluate();
Serial.print(F("Current="));
Serial.print(currentA, 2);
Serial.print(F("A"));
Serial.print(F(", status=")); Serial.println(statusText);
updateDisplay();
}
setBuzzer(alertOn && (millis() / 250) % 2 == 0); // intermittent beep
setRedLed(alertOn && (millis() / 250) % 2 == 0);
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
The zero point was taken with the load on. Switch the load off and reset the board.
Current flows the other way. Swap the wires on IP+ and IP−, or ignore the sign.
Check SDA/SCL and try address 0x3D. Run an I²C scanner to confirm.
Low-triggered module: invert the logic in setBuzzer().
LED is reversed; flip it. Check the 220 Ω resistor is in series.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
It stops the output flickering on and off when the reading hovers right at the limit. The output switches on at ALERT_LEVEL and only switches off once the reading has moved back by the hysteresis amount.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider. Analog readings run 0–4095 instead of 0–1023, which the ADC_MAX constant handles.
Use a 5 V USB phone charger or a power bank into the board's USB port.
8 parts: Nano CH340 Development Board (Soldered), ACS712 Hall-Effect Current Sensor Module (5A), 0.96" OLED Display 128x64 (I2C), Active Buzzer Module 3.3–5V, Through-Hole LED Pack (Pack of 10), Resistor Assortment Kit (30 Values), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1 hour. The build on this page has 10 steps.
No. This page has the complete, tested code (dc_pump_idle_current_alarm.ino). Install these libraries first: Adafruit SSD1306 and Adafruit GFX Library.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹593 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Active vs passive buzzers; Current-limiting resistors for LEDs; Drawing text on an I²C display; Hall-effect current sensing.
Use it only on 12 V DC pumps and battery circuits. Never put the ACS712 module on mains wiring.
Ideas that reuse this build: Motor stall current cut-off and DC current meter. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Current=0.00A, status=PUMP DRY OR OFF Current=0.00A, status=PUMP DRY OR OFF Current=0.00A, status=PUMP DRY OR OFF Current=0.00A, status=PUMP DRY OR OFF Current=0.00A, status=PUMP DRY OR OFF Current=0.00A, status=PUMP DRY OR OFF Current=0.00A, status=PUMP DRY OR OFF Current=0.00A, status=PUMP DRY OR OFF
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.