LM317 variable power supply
Turn a 12 V adapter into an adjustable 1.25–10 V supply for your experiments.
Shop by category
Shop all componentsThe ACS712 sits in the + wire of the circuit and gives a voltage that follows the current. The Nano averages a hundred readings to steady the number and shows the amps on the display. Switch the load off while the Nano starts so it can measure the zero point.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Measures the current flowing through its two screw terminals with a Hall sensor, so the measured circuit stays electrically separate from the board.
Bright 4-digit 7-segment display driven by two wires.
Follow the colours: red is power, dark grey is ground, blue is a signal.
dc_current_meter_7seg.inoVerify & upload in Electrolark// DC current meter with a big display
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "dc-current-meter-7seg"
#include <TM1637Display.h>
// ---- pins ----
const uint8_t CURRENT_PIN = A0;
const uint8_t SEG_CLK = 2;
const uint8_t SEG_DIO = 3;
const int ADC_MAX = 1023; // 10-bit analog input
const float VREF = 5.0f;
const float ACS_MV_PER_A = 185.0; // 5 A module: 185 mV per amp (20 A: 100, 30 A: 66)
float acsZero = 0; // output with no current, measured at start-up
TM1637Display seg(SEG_CLK, SEG_DIO);
// ---- latest readings ----
float currentA = 0;
const unsigned long READ_EVERY_MS = 300;
unsigned long lastRead = 0;
const char* statusText = "OK";
float readCurrentA() {
long s = 0;
for (int i = 0; i < 100; i++) s += analogRead(CURRENT_PIN); // average out the noise
float mv = (s / 100.0f - acsZero) * VREF * 1000.0f / ADC_MAX;
float a = mv / ACS_MV_PER_A;
return fabs(a) < 0.05f ? 0 : a;
}
void updateDisplay() {
{ float segV = currentA; // shows 0.00 to 9.99, then 10.0 to 99.9, with a decimal point
if (segV < 0) seg.showNumberDec((int)round(segV), false);
else {
segV = min(segV, 99.9f);
int n = segV < 10 ? (int)round(segV * 100) : (int)round(segV * 10);
uint8_t s[4] = {seg.encodeDigit(n / 100 % 10), seg.encodeDigit(n / 10 % 10), seg.encodeDigit(n % 10), 0};
s[segV < 10 ? 0 : 1] |= 0x80; // decimal point
seg.setSegments(s);
}
}
}
void setup() {
Serial.begin(115200);
{ long s = 0; for (int i = 0; i < 200; i++) { s += analogRead(CURRENT_PIN); delay(1); } acsZero = s / 200.0f; } // switch the load off while the board starts
seg.setBrightness(5);
seg.clear();
}
void loop() {
if (millis() - lastRead < READ_EVERY_MS) return;
lastRead = millis();
currentA = readCurrentA();
Serial.print(F("Current="));
Serial.print(currentA, 2);
Serial.print(F("A"));
Serial.println();
updateDisplay();
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
The zero point was taken with the load on. Switch the load off and reset the board.
Current flows the other way. Swap the wires on IP+ and IP−, or ignore the sign.
CLK and DIO swapped; swap them.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider. Analog readings run 0–4095 instead of 0–1023, which the ADC_MAX constant handles.
Use a 5 V USB phone charger or a power bank into the board's USB port.
5 parts: Nano CH340 Development Board (Soldered), ACS712 Hall-Effect Current Sensor Module (5A), TM1637 4-Digit 7-Segment Display Module, Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 45 minutes. The build on this page has 8 steps.
No. This page has the complete, tested code (dc_current_meter_7seg.ino). Install this library first: TM1637.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹406 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Hall-effect current sensing; Multiplexed 7-segment displays.
Ideas that reuse this build: Motor stall cut-off and Solar panel power meter. They are listed under Take it further on this page.
Turn a 12 V adapter into an adjustable 1.25–10 V supply for your experiments.
Build your own USB power bank and learn how lithium charging works.
Free power for outdoor sensors: sunlight in, 5 V USB out.
Beeps when the mains goes off at night, so the fridge and the alarm clock do not quietly die.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Current=0.00A Current=0.00A Current=0.00A Current=0.00A Current=0.00A Current=0.00A Current=0.00A Current=0.00A
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.