LM317 variable power supply
Turn a 12 V adapter into an adjustable 1.25–10 V supply for your experiments.
Shop by category
Shop all componentsThe Nano runs from an 18650 cell kept charged by the TP4056, so it keeps working when the power fails. The divider watches the 5 V adapter output: when it drops the green light goes out and the buzzer sounds. Good for aquariums, freezers and anyone who sleeps through silence.
Tick anything you already have and the total updates.
Two resistors scale the battery voltage down by 11 so an analog pin can measure up to about 50 V safely.; 220 Ω series resistor for each LED
Active buzzer with a built-in oscillator: apply power and it beeps at about 2.3 kHz.
Charges the cell from the adapter and passes power to the Nano
Raises the cell's 3.0–4.2 V to a steady 5 V for the board
Follow the colours: red is power, dark grey is ground, blue is a signal.
Set the boost converter to 5.0 V with a multimeter before connecting the board. Cell + → TP4056 B+ and TP4056 OUT+ → boost IN+, cell − (TP4056 OUT−) → boost IN−, then boost OUT+ → board 5V pin and OUT− → GND. A bare 18650 (3.0–4.2 V) cannot run a 5 V board by itself.
power_cut_alarm.inoVerify & upload in Electrolark// Power-cut alarm with battery backup
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "power-cut-alarm"
// ---- pins ----
const uint8_t VBAT_PIN = A0;
const uint8_t BUZZER_PIN = 2;
const uint8_t LED_GREEN = 3;
const int ADC_MAX = 1023; // 10-bit analog input
const float VREF = 5.0f;
// ---- latest readings ----
float batteryV = 0;
const unsigned long READ_EVERY_MS = 1000;
unsigned long lastRead = 0;
bool alertOn = false;
const char* statusText = "Starting";
const float ALERT_LEVEL = 4.0; // the adapter output falls to 0 V within a second of a cut
const float HYSTERESIS = 0.5; // gap that stops rapid on/off switching
float readBatteryV() { return analogRead(VBAT_PIN) * VREF / ADC_MAX * 11.0f; } // 100 kΩ : 10 kΩ divider = ÷11
void setBuzzer(bool on) { digitalWrite(BUZZER_PIN, on ? HIGH : LOW); }
void setGreenLed(bool on) { digitalWrite(LED_GREEN, on ? HIGH : LOW); }
void evaluate() {
if (!alertOn && batteryV < ALERT_LEVEL) alertOn = true;
else if (alertOn && batteryV > ALERT_LEVEL + HYSTERESIS) alertOn = false;
statusText = alertOn ? "MAINS OFF" : "Mains OK";
}
void setup() {
Serial.begin(115200);
pinMode(BUZZER_PIN, OUTPUT);
setBuzzer(false);
pinMode(LED_GREEN, OUTPUT);
}
void loop() {
if (millis() - lastRead >= READ_EVERY_MS) {
lastRead = millis();
batteryV = readBatteryV();
evaluate();
Serial.print(F("Battery="));
Serial.print(batteryV, 2);
Serial.print(F("V"));
Serial.print(F(", status=")); Serial.println(statusText);
}
setBuzzer(alertOn && (millis() / 250) % 2 == 0); // intermittent beep
setGreenLed(!alertOn);
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Measure the real resistor values and change 11.0 to (R1 + R2) / R2.
Low-triggered module: invert the logic in setBuzzer().
LED is reversed; flip it. Check the 220 Ω resistor is in series.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
It stops the output flickering on and off when the reading hovers right at the limit. The output switches on at ALERT_LEVEL and only switches off once the reading has moved back by the hysteresis amount.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider. Analog readings run 0–4095 instead of 0–1023, which the ADC_MAX constant handles.
Use a 5 V USB phone charger or a power bank into the board's USB port.
10 parts: Nano CH340 Development Board (Soldered), Resistor Assortment Kit (30 Values), Active Buzzer Module 3.3–5V, Through-Hole LED Pack (Pack of 10), 18650 Battery Holder, 18650 Li-ion Rechargeable Cell 2600mAh, TP4056 1A Li-ion Charger Module with Protection, MT3608 Mini Boost Converter Module, Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 1–2 hours. The build on this page has 9 steps.
No. This page has the complete, tested code (power_cut_alarm.ino).
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹559 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Active vs passive buzzers; Current-limiting resistors for LEDs; Voltage dividers and ADC scaling.
Ideas that reuse this build: Battery voltage monitor with a gauge and Wi-Fi outage logger. They are listed under Take it further on this page.
Turn a 12 V adapter into an adjustable 1.25–10 V supply for your experiments.
Build your own USB power bank and learn how lithium charging works.
Free power for outdoor sensors: sunlight in, 5 V USB out.
Touch the probes to any battery up to 50 V and read its voltage in big digits.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Battery=16.45V, status=Mains OK Battery=16.45V, status=Mains OK
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.