LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsThe AD8232 amplifies the tiny electrical signal of the heart picked up by three sticky electrodes, and the Nano sends it to the Serial Plotter on your computer. You will see the classic spike of each heartbeat. It is a wonderful biology and electronics lesson.
A learning project, not a medical device, so never use it to diagnose anything. Power it from a battery only: never connect electrodes to a person while the board is connected to a mains-powered laptop or charger.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Amplifies the tiny electrical signal of the heart picked up by three sticky electrodes, so you can see an ECG-style trace on the Serial Plotter.
Follow the colours: red is power, dark grey is ground, blue is a signal.
ecg_heartbeat_plotter.inoVerify & upload in Electrolark// ECG heartbeat plotter
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "ecg-heartbeat-plotter"
// ---- pins ----
const uint8_t ECG_PIN = A0;
const uint8_t ECG_LOP = 2;
const uint8_t ECG_LON = 3;
// ---- latest readings ----
int ecgRaw = 0;
bool leadsOff = false;
const unsigned long READ_EVERY_MS = 10;
unsigned long lastRead = 0;
const char* statusText = "OK";
void setup() {
Serial.begin(115200);
pinMode(ECG_LOP, INPUT);
pinMode(ECG_LON, INPUT);
}
void loop() {
if (millis() - lastRead < READ_EVERY_MS) return;
lastRead = millis();
ecgRaw = analogRead(ECG_PIN);
leadsOff = digitalRead(ECG_LOP) == HIGH || digitalRead(ECG_LON) == HIGH;
Serial.print(F("ECG="));
Serial.print(ecgRaw);
Serial.println();
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
The electrodes have lost contact. Press them on clean, dry skin and check the leads-off flag.
Sit still, keep wires short and away from mains cables, and run from a battery.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider. Analog readings run 0–4095 instead of 0–1023, which the ADC_MAX constant handles.
Use a 5 V USB phone charger or a power bank into the board's USB port.
4 parts: Nano CH340 Development Board (Soldered), AD8232 ECG Heart Rate Monitoring Sensor Module Kit with Electrode Pads & Cable, Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1 hour. The build on this page has 7 steps.
No. This page has the complete, tested code (ecg_heartbeat_plotter.ino).
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹841 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Biosignals and amplifiers.
A learning project, not a medical device, so never use it to diagnose anything. Power it from a battery only: never connect electrodes to a person while the board is connected to a mains-powered laptop or charger.
Ideas that reuse this build: Heart rate monitor and Pulse sensor plotter. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
ECG=307 ECG=307 ECG=307 ECG=307 ECG=307 ECG=307 ECG=308 ECG=306 ECG=307
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.