LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsThe analog pulse sensor outputs a waveform you can watch in Tools → Serial Plotter. The sketch sets its own threshold from the signal and blinks the LED in time with each beat.
Not a medical device. Readings are for learning and must not be used for diagnosis.
Every main part of this project is an item on the public Package 1 equipment list, so a school lab that already owns Package 1 can build it without buying anything extra.
See the full Atal Tinkering Lab packages →
Geekobot is an independent shop, not endorsed by or affiliated with NITI Aayog or the Atal Innovation Mission. Item names follow the public AIM equipment list.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
Optical heart-pulse sensor for a fingertip or earlobe: an LED and light sensor with a filter and amplifier.
Follow the colours: red is power, dark grey is ground, blue is a signal.
pulse_sensor_plotter.inoVerify & upload in Electrolark// Pulse sensor heartbeat plotter
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "pulse-sensor-plotter"
// ---- pins ----
const uint8_t PULSE_PIN = A0;
const uint8_t LED_RED = 2;
const int ADC_MAX = 1023; // 10-bit analog input
const float VREF = 5.0f;
int THRESHOLD = 0; // set automatically from the signal
int signalMax = 0, signalMin = 4095;
bool inBeat = false;
unsigned long lastBeat = 0;
int bpm = 0;
unsigned long windowStart = 0;
void setRedLed(bool on) { digitalWrite(LED_RED, on ? HIGH : LOW); }
void setup() {
Serial.begin(115200);
pinMode(LED_RED, OUTPUT);
}
void loop() {
int v = analogRead(PULSE_PIN);
if (v > signalMax) signalMax = v;
if (v < signalMin) signalMin = v;
if (millis() - windowStart > 2000) { // re-centre the threshold every 2 s
THRESHOLD = (signalMax + signalMin) / 2 + (signalMax - signalMin) / 6;
signalMax = 0; signalMin = ADC_MAX; windowStart = millis();
}
if (!inBeat && v > THRESHOLD && THRESHOLD > 0) {
inBeat = true;
unsigned long gap = millis() - lastBeat;
if (gap > 300 && gap < 2000) bpm = 60000 / gap;
lastBeat = millis();
setRedLed(true);
} else if (inBeat && v < THRESHOLD) {
inBeat = false;
setRedLed(false);
}
Serial.print(v); Serial.print(' '); Serial.print(THRESHOLD); Serial.print(' '); Serial.println(bpm * 4); // view in the Serial Plotter
delay(10);
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Hold the finger steady and adjust THRESHOLD after watching the Serial Plotter.
LED is reversed; flip it. Check the 220 Ω resistor is in series.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider. Analog readings run 0–4095 instead of 0–1023, which the ADC_MAX constant handles.
Use a 5 V USB phone charger or a power bank into the board's USB port.
7 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, Pulse Sensor Heart Rate Monitor – Module Only, Through-Hole LED Pack (Pack of 10), Resistor Assortment Kit (30 Values), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 45 minutes. The build on this page has 7 steps.
No. This page has the complete, tested code (pulse_sensor_plotter.ino).
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹519 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Current-limiting resistors for LEDs; Peak detection on a noisy signal.
Not a medical device. Readings are for learning and must not be used for diagnosis.
Ideas that reuse this build: MAX30102 with OLED. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
307 307 0 307 307 0 307 307 0 307 307 0 307 307 0 307 307 0 307 307 0 308 307 0
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.