GPS speedometer and clock
A bike or car speedometer that needs no wheel sensor: satellites do the measuring.
Shop by category
Shop all componentsThe camera sits on a shelf facing the cot or bed and streams to a phone on your home Wi-Fi only. Turn the flash off at night. It does not replace being there, but helps you check without opening the door.
Tell people that a camera is there, and do not point it at neighbours' windows, bathrooms or the road. Follow your local privacy rules.
A viewing aid only, not a medical or baby-safety monitor. Keep it on your private Wi-Fi and change the default network passwords.
Tick anything you already have and the total updates.
The brain of the project; The bright white LED next to the camera lens, on GPIO 4.
Follow the colours: red is power, dark grey is ground, blue is a signal.
esp32_cam_nursery_room_viewer.inoVerify & upload in Electrolark// Nursery and sick-room viewer
// Geekobot project library · board: ESP32-CAM
// Wiring diagram, parts list and build steps: Geekobot project page "esp32-cam-nursery-room-viewer"
#include "esp_camera.h"
#include <WiFi.h>
#include <WebServer.h>
// ---- pins ----
const uint8_t FLASH_PIN = 4;
const char* WIFI_SSID = "YOUR_WIFI_NAME"; // 2.4 GHz network
const char* WIFI_PASS = "YOUR_WIFI_PASSWORD";
WebServer server(80);
void setFlash(bool on) { digitalWrite(FLASH_PIN, on ? HIGH : LOW); }
bool initCamera() {
camera_config_t cfg = {};
cfg.ledc_channel = LEDC_CHANNEL_0; cfg.ledc_timer = LEDC_TIMER_0;
cfg.pin_d0 = 5; cfg.pin_d1 = 18; cfg.pin_d2 = 19; cfg.pin_d3 = 21; cfg.pin_d4 = 36; cfg.pin_d5 = 39; cfg.pin_d6 = 34; cfg.pin_d7 = 35;
cfg.pin_xclk = 0; cfg.pin_pclk = 22; cfg.pin_vsync = 25; cfg.pin_href = 23;
cfg.pin_sccb_sda = 26; cfg.pin_sccb_scl = 27; cfg.pin_pwdn = 32; cfg.pin_reset = -1;
cfg.xclk_freq_hz = 20000000; cfg.pixel_format = PIXFORMAT_JPEG;
cfg.frame_size = FRAMESIZE_VGA; cfg.jpeg_quality = 12; cfg.fb_count = psramFound() ? 2 : 1;
cfg.fb_location = psramFound() ? CAMERA_FB_IN_PSRAM : CAMERA_FB_IN_DRAM;
cfg.grab_mode = CAMERA_GRAB_LATEST;
return esp_camera_init(&cfg) == ESP_OK;
}
void handleRoot() {
server.send(200, "text/html", "<!doctype html><html><body style='margin:0;background:#000;text-align:center'><img src='/stream' style='max-width:100%'><p style='color:#fff;font-family:sans-serif'><a style='color:#9cf' href='/jpg'>Snapshot</a> · <a style='color:#9cf' href='/flash'>Flash</a></p></body></html>");
}
void handleJpg() {
camera_fb_t* fb = esp_camera_fb_get();
if (!fb) { server.send(500, "text/plain", "Camera capture failed"); return; }
server.sendHeader("Content-Disposition", "inline; filename=capture.jpg");
server.send_P(200, "image/jpeg", (const char*)fb->buf, fb->len);
esp_camera_fb_return(fb);
}
void handleStream() {
WiFiClient client = server.client();
client.print("HTTP/1.1 200 OK\r\nContent-Type: multipart/x-mixed-replace; boundary=frame\r\n\r\n");
while (client.connected()) {
camera_fb_t* fb = esp_camera_fb_get();
if (!fb) break;
client.printf("--frame\r\nContent-Type: image/jpeg\r\nContent-Length: %u\r\n\r\n", fb->len);
client.write(fb->buf, fb->len);
client.print("\r\n");
esp_camera_fb_return(fb);
delay(30);
}
}
void handleFlash() {
static bool on = false;
on = !on; setFlash(on);
server.sendHeader("Location", "/"); server.send(302, "text/plain", "");
}
void setup() {
Serial.begin(115200);
pinMode(FLASH_PIN, OUTPUT); digitalWrite(FLASH_PIN, LOW);
if (!initCamera()) { Serial.println(F("Camera init failed: check the ribbon cable is seated")); }
WiFi.mode(WIFI_STA); WiFi.begin(WIFI_SSID, WIFI_PASS);
Serial.print(F("Connecting"));
while (WiFi.status() != WL_CONNECTED) { delay(500); Serial.print('.'); }
Serial.println(); Serial.print(F("Open http://")); Serial.println(WiFi.localIP());
server.on("/", handleRoot); server.on("/jpg", handleJpg); server.on("/stream", handleStream); server.on("/flash", handleFlash);
server.begin();
}
void loop() {
server.handleClient();
}
The sketch above runs here on a simulated ESP32-CAM. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Reseat the camera ribbon cable with the contacts facing the board; power from a 5 V 2 A supply, not a laptop USB port.
Move the board closer to the router and use a 5 V 2 A supply; weak power is the most common cause of poor streams.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Use a 5 V USB phone charger or a power bank into the board's USB port. Loads such as pumps, fans and solenoids need their own supply.
3 parts: ESP32 S-CAM-CH340 Development Board with OV2640 Camera, USB Breakout Board (Type-A female) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 1–2 hours. The build on this page has 6 steps.
No. This page has the complete, tested code (esp32_cam_nursery_room_viewer.ino).
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹847 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Tell people that a camera is there, and do not point it at neighbours' windows, bathrooms or the road. Follow your local privacy rules. A viewing aid only, not a medical or baby-safety monitor. Keep it on your private Wi-Fi and change the default network passwords.
Ideas that reuse this build: Live streaming camera and Motion-triggered camera. They are listed under Take it further on this page.
A bike or car speedometer that needs no wheel sensor: satellites do the measuring.
Records where you went every five seconds, ready to open on a map.
Two boards, two radios: press the button at the gate and it rings indoors.
Check temperature, humidity and pressure from any phone on your Wi-Fi.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Connecting... Open http://192.168.1.50
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.