LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsIn summer, shallow hatchery tanks and plastic-lined ponds heat up quickly, and fish eggs and fry are lost when the water gets too warm. The waterproof probe sits in the tank, and the buzzer and red LED warn at 32 °C so you can add cool water, shade the tank or run the aerator.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Waterproof stainless-steel probe that reads liquid or soil temperature from −55 to +125 °C (±0.5 °C).
Active buzzer with a built-in oscillator: apply power and it beeps at about 2.3 kHz.
4.7 kΩ pull-up between DATA and VCC; 220 Ω series resistor for each LED
Follow the colours: red is power, dark grey is ground, blue is a signal.
fish_hatchery_water_heat_alarm.inoVerify & upload in Electrolark// Fish hatchery water heat alarm
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "fish-hatchery-water-heat-alarm"
#include <OneWire.h>
#include <DallasTemperature.h>
// ---- pins ----
const uint8_t ONEWIRE_PIN = 2;
const uint8_t BUZZER_PIN = 3;
const uint8_t LED_RED = 4;
OneWire oneWire(ONEWIRE_PIN);
DallasTemperature probes(&oneWire);
// ---- latest readings ----
float probeC = 0;
const unsigned long READ_EVERY_MS = 2000;
unsigned long lastRead = 0;
bool alertOn = false;
const char* statusText = "Starting";
const float ALERT_LEVEL = 32; // fish eggs and fry are lost when hatchery water gets too warm
const float HYSTERESIS = 2; // gap that stops rapid on/off switching
float readProbeC() {
probes.requestTemperatures();
return probes.getTempCByIndex(0);
}
void setBuzzer(bool on) { digitalWrite(BUZZER_PIN, on ? HIGH : LOW); }
void setRedLed(bool on) { digitalWrite(LED_RED, on ? HIGH : LOW); }
void evaluate() {
if (!(probeC > -100)) { statusText = "Sensor error"; return; }
if (!alertOn && probeC > ALERT_LEVEL) alertOn = true;
else if (alertOn && probeC < ALERT_LEVEL - HYSTERESIS) alertOn = false;
statusText = alertOn ? "WATER HOT" : "Water OK";
}
void setup() {
Serial.begin(115200);
probes.begin();
pinMode(BUZZER_PIN, OUTPUT);
setBuzzer(false);
pinMode(LED_RED, OUTPUT);
}
void loop() {
if (millis() - lastRead >= READ_EVERY_MS) {
lastRead = millis();
probeC = readProbeC();
evaluate();
Serial.print(F("Probe="));
Serial.print(probeC, 1);
Serial.print(F("C"));
Serial.print(F(", status=")); Serial.println(statusText);
}
setBuzzer(alertOn && (millis() / 250) % 2 == 0); // intermittent beep
setRedLed(alertOn && (millis() / 250) % 2 == 0);
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
The 4.7 kΩ pull-up is missing or DATA is on the wrong pin. Check the yellow wire.
Low-triggered module: invert the logic in setBuzzer().
LED is reversed; flip it. Check the 220 Ω resistor is in series.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
It stops the output flickering on and off when the reading hovers right at the limit. The output switches on at ALERT_LEVEL and only switches off once the reading has moved back by the hysteresis amount.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
7 parts: Nano CH340 Development Board (Soldered), DS18B20 Waterproof Temperature Probe – 1m Cable, Active Buzzer Module 3.3–5V, Through-Hole LED Pack (Pack of 10), Resistor Assortment Kit (30 Values), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1 hour. The build on this page has 9 steps.
No. This page has the complete, tested code (fish_hatchery_water_heat_alarm.ino). Install these libraries first: OneWire and DallasTemperature.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹377 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
1-Wire bus and pull-up resistors; Active vs passive buzzers; Current-limiting resistors for LEDs.
Ideas that reuse this build: Fish pond temperature display and Fish pond aerator timer. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Probe=26.0C, status=Water OK
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.