Automatic dusk-to-dawn light
Lights switch on by themselves at dusk and off again in the morning.
Shop by category
Shop all componentsPond oxygen is lowest just before dawn, when algae have been using it all night. The relay runs the aerator for 30 minutes every two hours, round the clock, at a fraction of the power of running it non-stop. The bench model uses the mini pump in place of the aerator.
Field pumps run on mains or three-phase power. Have a licensed electrician fit a contactor and starter: never connect them to the relay module directly.
Keep to low-voltage loads unless a qualified electrician wires the mains side in an earthed, closed enclosure.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
An electrically isolated switch that lets a 3.3/5 V pin turn a 12 V (or mains) load on and off.
Mini pump for the bench model (a field pump goes through a contactor)
Follow the colours: red is power, dark grey is ground, blue is a signal.
The bench model runs the 3–6 V mini pump from a 4×AA holder through the relay (COM and NO). A mains or three-phase field pump must be switched by a contactor that an electrician wires; the relay only drives the contactor coil circuit he provides.
fish_pond_aerator_timer.inoVerify & upload in Electrolark// Fish pond aerator timer
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "fish-pond-aerator-timer"
// ---- pins ----
const uint8_t RELAY_PIN = 2;
const uint8_t LED_GREEN = 3;
const bool RELAY_ACTIVE_LOW = true; // most relay modules switch on when IN is LOW
const unsigned long ON_MS = 30 * 60000UL; // run time per cycle
const unsigned long EVERY_MS = 120 * 60000UL; // one cycle starts this often
unsigned long cycleStart = 0;
bool first = true;
void setRelay(bool on) { digitalWrite(RELAY_PIN, (on != RELAY_ACTIVE_LOW) ? HIGH : LOW); }
void setGreenLed(bool on) { digitalWrite(LED_GREEN, on ? HIGH : LOW); }
void setup() {
Serial.begin(115200);
pinMode(RELAY_PIN, OUTPUT);
setRelay(false);
pinMode(LED_GREEN, OUTPUT);
setRelay(false);
setGreenLed(false);
}
void loop() {
if (first || millis() - cycleStart >= EVERY_MS) { first = false; cycleStart = millis(); }
bool on = millis() - cycleStart < ON_MS && true;
setRelay(on);
setGreenLed(on);
static unsigned long lastLog = 0;
if (millis() - lastLog > 5000) { lastLog = millis(); Serial.print(on ? F("ON, ") : F("off, ")); Serial.print((EVERY_MS - (millis() - cycleStart)) / 60000); Serial.println(F(" min to next cycle")); }
delay(50);
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Load must be on COM and NO, with its own supply in series.
Your module may be active-HIGH. Set RELAY_ACTIVE_LOW to false.
Some 5 V relay boards do not fully switch off with 3.3 V logic. Remove the JD-VCC jumper, feed JD-VCC from 5 V and VCC from 3.3 V, or use a relay board made for 3.3 V input.
LED is reversed; flip it. Check the 220 Ω resistor is in series.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
The relay is rated for mains, but mains wiring is dangerous. Keep this build on low-voltage loads (12 V pumps, fans, LED strips), or have a qualified electrician fit the relay inside an earthed, closed enclosure.
Use a 5 V USB phone charger or a power bank into the board's USB port. Loads such as pumps, fans and solenoids need their own supply.
8 parts: Nano CH340 Development Board (Soldered), 5V Relay Module with Optocoupler (1 channel), Through-Hole LED Pack (Pack of 10), Resistor Assortment Kit (30 Values), Mini Submersible Water Pump 3–6V with 1m tube, Battery Holder (AA), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1 hour. The build on this page has 8 steps.
No. This page has the complete, tested code (fish_pond_aerator_timer.ino).
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹587 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Current-limiting resistors for LEDs; Isolation, relays and switching higher-power loads.
Ideas that reuse this build: Fish pond temperature display and Hydroponic pump timer. They are listed under Take it further on this page.
Lights switch on by themselves at dusk and off again in the morning.
A precise thermostat that keeps tropical fish at a steady 25–26 °C.
Starts the pump when the tank runs low and stops it when it is full.
Tap a hidden pad to switch a lamp on or off, even through a wooden desk.
Learning project. Check every circuit and the datasheet of each part before you power it up.
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.