LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsThe MLX90614 looks at the hot part from a few centimetres. Above the limit the relay starts the fan, and below it the fan stops, which keeps noise down when the part is cool.
This is a low-voltage bench model. A mains fan or pump must be switched by a qualified electrician with a rated contactor.
Keep the sensor and board away from mains parts.
Not a medical device. Readings are for learning and must not be used for diagnosis.
Keep to low-voltage loads unless a qualified electrician wires the mains side in an earthed, closed enclosure.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Infrared thermometer: measures the temperature of whatever it points at without touching it (field of view about 90°).
Classic 16-character, 2-line LCD with an I²C backpack, so it needs only two signal wires.
An electrically isolated switch that lets a 3.3/5 V pin turn a 12 V (or mains) load on and off.
Follow the colours: red is power, dark grey is ground, blue is a signal.
Adapter + to relay COM, relay NO to fan +, fan − to adapter −. Keep the fan supply separate from the board USB.
heatsink_infrared_cooling_fan.inoVerify & upload in Electrolark// Heat-sink infrared cooling fan
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "heatsink-infrared-cooling-fan"
#include <Wire.h>
#include <Adafruit_MLX90614.h>
#include <LiquidCrystal_I2C.h>
// ---- pins ----
const uint8_t RELAY_PIN = 2;
Adafruit_MLX90614 mlx;
LiquidCrystal_I2C lcd(0x27, 16, 2);
const bool RELAY_ACTIVE_LOW = true; // most relay modules switch on when IN is LOW
// ---- latest readings ----
float objC = 0;
float ambC = 0;
const unsigned long READ_EVERY_MS = 1000;
unsigned long lastRead = 0;
bool alertOn = false;
const char* statusText = "Starting";
const float ALERT_LEVEL = 55; // below the temperature the part is rated for
const float HYSTERESIS = 8; // gap that stops rapid on/off switching
void setRelay(bool on) { digitalWrite(RELAY_PIN, (on != RELAY_ACTIVE_LOW) ? HIGH : LOW); }
void updateDisplay() {
lcd.setCursor(0, 0);
lcd.print(F("Object "));
lcd.print(objC, 1);
lcd.print(F(" C"));
lcd.print(F(" "));
lcd.setCursor(0, 1);
lcd.print(F("Ambi "));
lcd.print(ambC, 1);
lcd.print(F(" C"));
lcd.print(F(" "));
lcd.print(statusText);
lcd.print(F(" "));
}
void evaluate() {
if (!alertOn && objC > ALERT_LEVEL) alertOn = true;
else if (alertOn && objC < ALERT_LEVEL - HYSTERESIS) alertOn = false;
statusText = alertOn ? "COOLING" : "Cool";
}
void setup() {
Serial.begin(115200);
if (!mlx.begin()) Serial.println(F("MLX90614 not found"));
lcd.init();
lcd.backlight();
pinMode(RELAY_PIN, OUTPUT);
setRelay(false);
}
void loop() {
if (millis() - lastRead >= READ_EVERY_MS) {
lastRead = millis();
objC = mlx.readObjectTempC();
ambC = mlx.readAmbientTempC();
evaluate();
Serial.print(F("Object="));
Serial.print(objC, 1);
Serial.print(F("C"));
Serial.print(F(", Ambient="));
Serial.print(ambC, 1);
Serial.print(F("C"));
Serial.print(F(", status=")); Serial.println(statusText);
updateDisplay();
}
setRelay(alertOn);
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
You are too far away, so the sensor sees mostly background. Move closer.
Adjust the contrast pot on the backpack. If still blank, change 0x27 to 0x3F.
Load must be on COM and NO, with its own supply in series.
Your module may be active-HIGH. Set RELAY_ACTIVE_LOW to false.
Some 5 V relay boards do not fully switch off with 3.3 V logic. Remove the JD-VCC jumper, feed JD-VCC from 5 V and VCC from 3.3 V, or use a relay board made for 3.3 V input.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
It stops the output flickering on and off when the reading hovers right at the limit. The output switches on at ALERT_LEVEL and only switches off once the reading has moved back by the hysteresis amount.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
The relay is rated for mains, but mains wiring is dangerous. Keep this build on low-voltage loads (12 V pumps, fans, LED strips), or have a qualified electrician fit the relay inside an earthed, closed enclosure.
Use a 5 V USB phone charger or a power bank into the board's USB port. Loads such as pumps, fans and solenoids need their own supply.
8 parts: Nano CH340 Development Board (Soldered), MLX90614 IR Non-Contact Temperature Sensor Module, LCD1602 16x2 Character LCD (blue, with I2C adapter), 5V Relay Module with Optocoupler (1 channel), 12V DC Brushless Fan 80mm (cooling fan), DC Power Adapter 12V 2A (5.5x2.1mm), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1 hour. The build on this page has 9 steps.
No. This page has the complete, tested code (heatsink_infrared_cooling_fan.ino). Install these libraries first: Adafruit MLX90614 Library and LiquidCrystal I2C.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹1,522 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Character displays and I²C backpacks; Contactless infrared temperature measurement; Isolation, relays and switching higher-power loads.
Ideas that reuse this build: Transformer and heat-sink heat alarm and Infrared thermometer pointer dial. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Object=34.9C, Ambient=25.9C, status=Cool Object=35.0C, Ambient=26.0C, status=Cool
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.