LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsThree ways to measure heat on one display. Heat a metal block and watch the thermocouple, the infrared sensor and the waterproof probe differ, which teaches students about emissivity and response time.
A learning and comparison aid, not a certified instrument.
Keep the board away from hot parts.
Not a medical device. Readings are for learning and must not be used for diagnosis.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Infrared thermometer: measures the temperature of whatever it points at without touching it (field of view about 90°).
Reads a K-type thermocouple probe up to 1,000 °C through an amplifier chip, which is the way to measure ovens, kilns, soldering irons and engines.
Waterproof stainless-steel probe that reads liquid or soil temperature from −55 to +125 °C (±0.5 °C).
Follow the colours: red is power, dark grey is ground, blue is a signal.
lab_thermal_board.inoVerify & upload in Electrolark// Lab thermal board
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "lab-thermal-board"
#include <Wire.h>
#include <Adafruit_MLX90614.h>
#include <max6675.h>
#include <OneWire.h>
#include <DallasTemperature.h>
#include <Adafruit_GFX.h>
#include <Adafruit_SSD1306.h>
// ---- pins ----
const uint8_t TC_SCK = 2;
const uint8_t TC_CS = 3;
const uint8_t TC_SO = 4;
const uint8_t ONEWIRE_PIN = 5;
Adafruit_MLX90614 mlx;
MAX6675 thermocouple(TC_SCK, TC_CS, TC_SO);
OneWire oneWire(ONEWIRE_PIN);
DallasTemperature probes(&oneWire);
Adafruit_SSD1306 oled(128, 64, &Wire, -1);
// ---- latest readings ----
float objC = 0;
float ambC = 0;
float probeC = 0;
const unsigned long READ_EVERY_MS = 1500;
unsigned long lastRead = 0;
const char* statusText = "OK";
float readProbeC() {
probes.requestTemperatures();
return probes.getTempCByIndex(0);
}
void updateDisplay() {
oled.clearDisplay();
oled.setTextSize(1);
oled.setCursor(0, 0);
oled.print(F("Thermal"));
oled.drawLine(0, 10, 127, 10, SSD1306_WHITE);
oled.setCursor(0, 14);
oled.print(F("Object: "));
oled.print(objC, 1);
oled.print(F(" C"));
oled.setCursor(0, 24);
oled.print(F("Ambient: "));
oled.print(ambC, 1);
oled.print(F(" C"));
oled.setCursor(0, 34);
oled.print(F("Probe: "));
oled.print(probeC, 0);
oled.print(F(" C"));
oled.setCursor(0, 44);
oled.print(F("Probe: "));
oled.print(probeC, 1);
oled.print(F(" C"));
oled.setCursor(0, 56);
oled.print(statusText);
oled.display();
}
void setup() {
Serial.begin(115200);
if (!mlx.begin()) Serial.println(F("MLX90614 not found"));
probes.begin();
if (!oled.begin(SSD1306_SWITCHCAPVCC, 0x3C)) Serial.println(F("OLED not found"));
oled.setTextColor(SSD1306_WHITE);
oled.clearDisplay();
oled.display();
}
void loop() {
if (millis() - lastRead < READ_EVERY_MS) return;
lastRead = millis();
objC = mlx.readObjectTempC();
ambC = mlx.readAmbientTempC();
probeC = thermocouple.readCelsius();
probeC = readProbeC();
statusText = (!isnan(probeC) && probeC > -100) ? "OK" : "Sensor error";
Serial.print(F("Object="));
Serial.print(objC, 1);
Serial.print(F("C"));
Serial.print(F(", Ambient="));
Serial.print(ambC, 1);
Serial.print(F("C"));
Serial.print(F(", Probe="));
Serial.print(probeC, 0);
Serial.print(F("C"));
Serial.print(F(", Probe="));
Serial.print(probeC, 1);
Serial.print(F("C"));
Serial.println();
updateDisplay();
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
You are too far away, so the sensor sees mostly background. Move closer.
The thermocouple is not connected or its plus and minus wires are swapped. Check the screw terminals.
The module also senses its own temperature at the cold junction. Keep it away from the heat you are measuring.
The 4.7 kΩ pull-up is missing or DATA is on the wrong pin. Check the yellow wire.
Check SDA/SCL and try address 0x3D. Run an I²C scanner to confirm.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
8 parts: Nano CH340 Development Board (Soldered), MLX90614 IR Non-Contact Temperature Sensor Module, MAX6675 Module with K-Type Thermocouple Probe, 50 cm Cable, DS18B20 Waterproof Temperature Probe – 1m Cable, 0.96" OLED Display 128x64 (I2C), Resistor Assortment Kit (30 Values), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 2–3 hours. The build on this page has 10 steps.
No. This page has the complete, tested code (lab_thermal_board.ino). Install these libraries first: Adafruit MLX90614 Library, MAX6675 library, OneWire, DallasTemperature, Adafruit SSD1306 and Adafruit GFX Library.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹1,480 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
1-Wire bus and pull-up resistors; Contactless infrared temperature measurement; Drawing text on an I²C display; Thermocouples and cold-junction compensation.
A learning and comparison aid, not a certified instrument. Keep the board away from hot parts. Not a medical device. Readings are for learning and must not be used for diagnosis.
Ideas that reuse this build: Lab bench heat and fume logger and Stepper furnace temperature dial. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Object=34.9C, Ambient=25.9C, Probe=26C, Probe=26.0C
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.