LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsLED strips often draw more than the printed rating when they are fully white. Place the ACS712 in the supply wire and the OLED shows the current in amps, which tells you whether your adapter and wires have enough margin.
Low-voltage DC circuits only.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Measures the current flowing through its two screw terminals with a Hall sensor, so the measured circuit stays electrically separate from the board.
Follow the colours: red is power, dark grey is ground, blue is a signal.
led_strip_current_budget_meter.inoVerify & upload in Electrolark// LED strip current budget meter
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "led-strip-current-budget-meter"
#include <Wire.h>
#include <Adafruit_GFX.h>
#include <Adafruit_SSD1306.h>
// ---- pins ----
const uint8_t CURRENT_PIN = A0;
const int ADC_MAX = 1023; // 10-bit analog input
const float VREF = 5.0f;
const float ACS_MV_PER_A = 185.0; // 5 A module: 185 mV per amp (20 A: 100, 30 A: 66)
float acsZero = 0; // output with no current, measured at start-up
Adafruit_SSD1306 oled(128, 64, &Wire, -1);
// ---- latest readings ----
float currentA = 0;
const unsigned long READ_EVERY_MS = 500;
unsigned long lastRead = 0;
const char* statusText = "OK";
float readCurrentA() {
long s = 0;
for (int i = 0; i < 100; i++) s += analogRead(CURRENT_PIN); // average out the noise
float mv = (s / 100.0f - acsZero) * VREF * 1000.0f / ADC_MAX;
float a = mv / ACS_MV_PER_A;
return fabs(a) < 0.05f ? 0 : a;
}
void updateDisplay() {
oled.clearDisplay();
oled.setTextSize(1);
oled.setCursor(0, 0);
oled.print(F("LED strip"));
oled.drawLine(0, 10, 127, 10, SSD1306_WHITE);
oled.setCursor(0, 16);
oled.print(F("Current"));
oled.setTextSize(2);
oled.setCursor(0, 28);
oled.print(currentA, 2);
oled.print(F(" A"));
oled.setTextSize(1);
oled.display();
}
void setup() {
Serial.begin(115200);
{ long s = 0; for (int i = 0; i < 200; i++) { s += analogRead(CURRENT_PIN); delay(1); } acsZero = s / 200.0f; } // switch the load off while the board starts
if (!oled.begin(SSD1306_SWITCHCAPVCC, 0x3C)) Serial.println(F("OLED not found"));
oled.setTextColor(SSD1306_WHITE);
oled.clearDisplay();
oled.display();
}
void loop() {
if (millis() - lastRead < READ_EVERY_MS) return;
lastRead = millis();
currentA = readCurrentA();
Serial.print(F("Current="));
Serial.print(currentA, 2);
Serial.print(F("A"));
Serial.println();
updateDisplay();
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
The zero point was taken with the load on. Switch the load off and reset the board.
Current flows the other way. Swap the wires on IP+ and IP−, or ignore the sign.
Check SDA/SCL and try address 0x3D. Run an I²C scanner to confirm.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider. Analog readings run 0–4095 instead of 0–1023, which the ADC_MAX constant handles.
Use a 5 V USB phone charger or a power bank into the board's USB port.
5 parts: Nano CH340 Development Board (Soldered), ACS712 Hall-Effect Current Sensor Module (5A), 0.96" OLED Display 128x64 (I2C), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1 hour. The build on this page has 8 steps.
No. This page has the complete, tested code (led_strip_current_budget_meter.ino). Install these libraries first: Adafruit SSD1306 and Adafruit GFX Library.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹518 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Drawing text on an I²C display; Hall-effect current sensing.
Low-voltage DC circuits only.
Ideas that reuse this build: DC current meter on 7-segment and USB power meter. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Current=0.00A Current=0.00A Current=0.00A Current=0.00A Current=0.00A
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.