LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsCyclones and heavy storms come with a deep drop in air pressure. The BMP180 on the LCD shows the pressure and trips a warning below 1,000 hPa, giving you a reason to check the forecast, bring in washing and charge the torches.
A learning aid, not an official warning. Follow the weather department's alerts for storms and cyclones.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Measures air pressure over I²C.
Classic 16-character, 2-line LCD with an I²C backpack, so it needs only two signal wires.
Active buzzer with a built-in oscillator: apply power and it beeps at about 2.3 kHz.
Follow the colours: red is power, dark grey is ground, blue is a signal.
low_pressure_storm_watch.inoVerify & upload in Electrolark// Low-pressure storm watch
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "low-pressure-storm-watch"
#include <Wire.h>
#include <Adafruit_BMP085_U.h>
#include <LiquidCrystal_I2C.h>
// ---- pins ----
const uint8_t BUZZER_PIN = 2;
const uint8_t LED_YELLOW = 3;
Adafruit_BMP085_Unified bmp = Adafruit_BMP085_Unified(10085);
LiquidCrystal_I2C lcd(0x27, 16, 2);
// ---- latest readings ----
float pressHpa = 0;
float bmpC = 0;
const unsigned long READ_EVERY_MS = 1000;
unsigned long lastRead = 0;
bool alertOn = false;
const char* statusText = "Starting";
const float ALERT_LEVEL = 1000; // sea-level pressure below about 1000 hPa is a stormy sign; adjust for your height
const float HYSTERESIS = 2; // gap that stops rapid on/off switching
float bmp180Hpa() { sensors_event_t e; bmp.getEvent(&e); return e.pressure; }
float bmp180C() { float t = 0; bmp.getTemperature(&t); return t; }
void setBuzzer(bool on) { digitalWrite(BUZZER_PIN, on ? HIGH : LOW); }
void setYellowLed(bool on) { digitalWrite(LED_YELLOW, on ? HIGH : LOW); }
void updateDisplay() {
lcd.setCursor(0, 0);
lcd.print(F("Pressure "));
lcd.print(pressHpa, 1);
lcd.print(F(" hPa"));
lcd.print(F(" "));
lcd.setCursor(0, 1);
lcd.print(F("Temp "));
lcd.print(bmpC, 1);
lcd.print(F(" C"));
lcd.print(F(" "));
lcd.print(statusText);
lcd.print(F(" "));
}
void evaluate() {
if (!alertOn && pressHpa < ALERT_LEVEL) alertOn = true;
else if (alertOn && pressHpa > ALERT_LEVEL + HYSTERESIS) alertOn = false;
statusText = alertOn ? "LOW PRESSURE" : "Normal pressure";
}
void setup() {
Serial.begin(115200);
if (!bmp.begin()) Serial.println(F("BMP180 not found"));
lcd.init();
lcd.backlight();
pinMode(BUZZER_PIN, OUTPUT);
setBuzzer(false);
pinMode(LED_YELLOW, OUTPUT);
}
void loop() {
if (millis() - lastRead >= READ_EVERY_MS) {
lastRead = millis();
pressHpa = bmp180Hpa();
bmpC = bmp180C();
evaluate();
Serial.print(F("Pressure="));
Serial.print(pressHpa, 1);
Serial.print(F("hPa"));
Serial.print(F(", Temp="));
Serial.print(bmpC, 1);
Serial.print(F("C"));
Serial.print(F(", status=")); Serial.println(statusText);
updateDisplay();
}
setBuzzer(alertOn && (millis() / 250) % 2 == 0); // intermittent beep
setYellowLed(alertOn);
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Check SDA and SCL. An I²C scanner should show 0x77.
That is the sea-level figure. Use the change from your first reading to see height and weather.
Adjust the contrast pot on the backpack. If still blank, change 0x27 to 0x3F.
Low-triggered module: invert the logic in setBuzzer().
LED is reversed; flip it. Check the 220 Ω resistor is in series.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
It stops the output flickering on and off when the reading hovers right at the limit. The output switches on at ALERT_LEVEL and only switches off once the reading has moved back by the hysteresis amount.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
8 parts: Nano CH340 Development Board (Soldered), BMP180 Digital Barometric Pressure Sensor Module – I2C Interface, LCD1602 16x2 Character LCD (blue, with I2C adapter), Active Buzzer Module 3.3–5V, Through-Hole LED Pack (Pack of 10), Resistor Assortment Kit (30 Values), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1 hour. The build on this page has 10 steps.
No. This page has the complete, tested code (low_pressure_storm_watch.ino). Install these libraries first: Adafruit BMP085 Unified and LiquidCrystal I2C.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹469 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Active vs passive buzzers; Barometric pressure and altitude; Character displays and I²C backpacks; Current-limiting resistors for LEDs.
A learning aid, not an official warning. Follow the weather department's alerts for storms and cyclones.
Ideas that reuse this build: BMP180 pressure and weather watcher and Pressure trend ring. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Pressure=1007.8hPa, Temp=25.9C, status=Normal pressure Pressure=1008.0hPa, Temp=26.0C, status=Normal pressure
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.