LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsA dry coolant pump burns out and a dry cutting tool loses its edge. The sensor board hangs in the coolant sump at the minimum level; once the coolant drops below it, the red light and buzzer call for a top-up.
Every main part of this project is an item on the public Package 1 equipment list, so a school lab that already owns Package 1 can build it without buying anything extra.
See the full Atal Tinkering Lab packages →
Geekobot is an independent shop, not endorsed by or affiliated with NITI Aayog or the Atal Innovation Mission. Item names follow the public AIM equipment list.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Comb-patterned plate whose resistance drops when water bridges the tracks.
Active buzzer with a built-in oscillator: apply power and it beeps at about 2.3 kHz.
Follow the colours: red is power, dark grey is ground, blue is a signal.
machine_coolant_low_alarm.inoVerify & upload in Electrolark// Machine coolant tank low alarm
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "machine-coolant-low-alarm"
// ---- pins ----
const uint8_t RAIN_PIN = A0;
const uint8_t BUZZER_PIN = 2;
const uint8_t LED_RED = 3;
const int ADC_MAX = 1023; // 10-bit analog input
const float VREF = 5.0f;
// ---- latest readings ----
int wetPct = 0;
const unsigned long READ_EVERY_MS = 2000;
unsigned long lastRead = 0;
bool alertOn = false;
const char* statusText = "Starting";
const float ALERT_LEVEL = 25; // the probe is above the coolant
const float HYSTERESIS = 10; // gap that stops rapid on/off switching
void setBuzzer(bool on) { digitalWrite(BUZZER_PIN, on ? HIGH : LOW); }
void setRedLed(bool on) { digitalWrite(LED_RED, on ? HIGH : LOW); }
void evaluate() {
if (!alertOn && wetPct < ALERT_LEVEL) alertOn = true;
else if (alertOn && wetPct > ALERT_LEVEL + HYSTERESIS) alertOn = false;
statusText = alertOn ? "TOP UP" : "OK";
}
void setup() {
Serial.begin(115200);
pinMode(BUZZER_PIN, OUTPUT);
setBuzzer(false);
pinMode(LED_RED, OUTPUT);
}
void loop() {
if (millis() - lastRead >= READ_EVERY_MS) {
lastRead = millis();
wetPct = (int)(100 - analogRead(RAIN_PIN) * 100L / ADC_MAX);
evaluate();
Serial.print(F("Rain="));
Serial.print(wetPct);
Serial.print(F("%"));
Serial.print(F(", status=")); Serial.println(statusText);
}
setBuzzer(alertOn && (millis() / 250) % 2 == 0); // intermittent beep
setRedLed(alertOn && (millis() / 250) % 2 == 0);
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Dry the plate and clean off residue. Powering it only when reading slows corrosion.
Low-triggered module: invert the logic in setBuzzer().
LED is reversed; flip it. Check the 220 Ω resistor is in series.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
It stops the output flickering on and off when the reading hovers right at the limit. The output switches on at ALERT_LEVEL and only switches off once the reading has moved back by the hysteresis amount.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider. Analog readings run 0–4095 instead of 0–1023, which the ADC_MAX constant handles.
Use a 5 V USB phone charger or a power bank into the board's USB port.
7 parts: Nano CH340 Development Board (Soldered), HS-S09-PB Rain Sensor Kit – Analog/Digital Output, Active Buzzer Module 3.3–5V, Through-Hole LED Pack (Pack of 10), Resistor Assortment Kit (30 Values), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 45 minutes. The build on this page has 9 steps.
No. This page has the complete, tested code (machine_coolant_low_alarm.ino).
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹546 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Active vs passive buzzers; Current-limiting resistors for LEDs; Resistive sensing and corrosion.
Ideas that reuse this build: Air cooler refill alarm and Machine hour meter. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Rain=71%, status=OK
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.