Remote-controlled RGB mood light
Warm, cool, rainbow or breathing: cycle lighting moods from your sofa.
Shop by category
Shop all componentsThe sound module measures how loud it is every 50 ms. The Nano keeps the last eight values, turns each into a bar of up to eight dots and draws them side by side, so the picture scrolls as time passes. A simple music visualiser and a good lesson on arrays.
Every main part of this project is an item on the public Package 1 equipment list, so a school lab that already owns Package 1 can build it without buying anything extra.
See the full Atal Tinkering Lab packages →
Geekobot is an independent shop, not endorsed by or affiliated with NITI Aayog or the Atal Innovation Mission. Item names follow the public AIM equipment list.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
64 red LEDs in an 8×8 grid driven by one MAX7219 chip over three wires.
Follow the colours: red is power, dark grey is ground, blue is a signal.
matrix_sound_bars.inoVerify & upload in Electrolark// LED matrix sound bar graph
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "matrix-sound-bars"
#include <LedControl.h>
// ---- pins ----
const uint8_t MX_DIN = 2;
const uint8_t MX_CS = 3;
const uint8_t MX_CLK = 4;
const uint8_t MIC_PIN = A0;
const int ADC_MAX = 1023; // 10-bit analog input
const float VREF = 5.0f;
LedControl matrix(MX_DIN, MX_CLK, MX_CS, 1);
// ---- latest readings ----
int soundPct = 0;
int heights[8] = {0, 0, 0, 0, 0, 0, 0, 0};
int readSoundLevel() {
// peak-to-peak amplitude over a 50 ms window
unsigned long start = millis();
int lo = ADC_MAX, hi = 0;
while (millis() - start < 50) {
int v = analogRead(MIC_PIN);
if (v < lo) lo = v;
if (v > hi) hi = v;
}
return (int)((hi - lo) * 100L / ADC_MAX);
}
void setup() {
Serial.begin(115200);
matrix.shutdown(0, false);
matrix.setIntensity(0, 4);
matrix.clearDisplay(0);
}
void loop() {
int level = readSoundLevel(); // 0 to 100 percent
for (int i = 0; i < 7; i++) heights[i] = heights[i + 1]; // slide the history left
heights[7] = constrain(level / 6, 0, 8); // one dot per 6 percent
for (int col = 0; col < 8; col++) {
byte bits = 0;
for (int r = 0; r < heights[col]; r++) bits |= (1 << r);
matrix.setColumn(0, col, bits);
}
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Check DIN/CLK/CS order and use short wires.
Turn the module trimmer to increase gain, or move the mic closer to the sound.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider. Analog readings run 0–4095 instead of 0–1023, which the ADC_MAX constant handles.
Use a 5 V USB phone charger or a power bank into the board's USB port.
5 parts: Nano CH340 Development Board (Soldered), MAX7219 8x8 LED Matrix Module, Analog Sound Sensor Microphone Module, Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 2 hours. The build on this page has 8 steps.
No. This page has the complete, tested code (matrix_sound_bars.ino). Install this library first: LedControl.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹440 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Sampling a waveform and measuring amplitude; Shift-register style LED drivers.
Ideas that reuse this build: Sound level ring and Pico sound level ring. They are listed under Take it further on this page.
Warm, cool, rainbow or breathing: cycle lighting moods from your sofa.
Press to roll: the pips tumble and slow down before landing on a number.
Wait for the light, hit the button: how many milliseconds can you beat?
A bright 4-digit clock that keeps time through power cuts.
Learning project. Check every circuit and the datasheet of each part before you power it up.
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.