LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsForgetting a tablet is easy; this box makes it hard. The DS3231 keeps accurate time through power cuts, the buzzer and red light pulse at each dose time, and pressing the button records the dose as taken. If nobody responds within 30 minutes the red light stays on as a missed-dose flag.
A reminder aid only. Follow the instructions of the doctor or pharmacist.
Tick anything you already have and the total updates.
Temperature-compensated real-time clock (±2 minutes a year) with a coin-cell backup, so the time survives power cuts.
Active buzzer with a built-in oscillator: apply power and it beeps at about 2.3 kHz.
Follow the colours: red is power, dark grey is ground, blue is a signal.
medicine_reminder_rtc.inoVerify & upload in Electrolark// Medicine reminder with three daily doses
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "medicine-reminder-rtc"
#include <Wire.h>
#include <RTClib.h>
// ---- pins ----
const uint8_t BUTTON_PIN = 2;
const uint8_t BUZZER_PIN = 3;
const uint8_t LED_RED = 4;
RTC_DS3231 rtc;
const int DOSE_HOUR[] = {8, 14, 21};
const int DOSE_MIN[] = {0, 0, 30};
const int DOSES = 3;
int alarmFor = -1; // index of the dose currently ringing
unsigned long alarmStart = 0;
int takenToday[3] = {0, 0, 0};
int lastDay = -1;
void setBuzzer(bool on) { digitalWrite(BUZZER_PIN, on ? HIGH : LOW); }
void setRedLed(bool on) { digitalWrite(LED_RED, on ? HIGH : LOW); }
void showTakenCount() {
int n = 0; for (int i = 0; i < DOSES; i++) n += takenToday[i];
Serial.print(F("Doses taken today: ")); Serial.print(n); Serial.print(F(" of ")); Serial.println(DOSES);
}
void setup() {
Serial.begin(115200);
if (!rtc.begin()) Serial.println(F("RTC not found"));
if (rtc.lostPower()) rtc.adjust(DateTime(F(__DATE__), F(__TIME__))); // set from the upload time
pinMode(BUTTON_PIN, INPUT_PULLUP);
pinMode(BUZZER_PIN, OUTPUT);
setBuzzer(false);
pinMode(LED_RED, OUTPUT);
}
void loop() {
DateTime now = rtc.now();
if (now.day() != lastDay) { lastDay = now.day(); for (int i = 0; i < DOSES; i++) takenToday[i] = 0; }
for (int i = 0; i < DOSES; i++)
if (!takenToday[i] && alarmFor < 0 && now.hour() == DOSE_HOUR[i] && now.minute() == DOSE_MIN[i]) { alarmFor = i; alarmStart = millis(); }
if (alarmFor >= 0) {
bool phase = (millis() / 400) % 2; // beep and flash until acknowledged
setBuzzer(phase); setRedLed(phase);
if (digitalRead(BUTTON_PIN) == LOW) { takenToday[alarmFor] = 1; alarmFor = -1; setBuzzer(false); setRedLed(false); showTakenCount(); delay(500); }
else if (millis() - alarmStart > 30UL * 60 * 1000) { alarmFor = -1; setBuzzer(false); setRedLed(true); } // 30 min: give up, leave the red light on
}
delay(50);
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
The coin cell is flat or missing. Some modules need the charging resistor removed when using a CR2032.
The button is rotated 90°; legs on the same side are already connected. Turn it.
Low-triggered module: invert the logic in setBuzzer().
LED is reversed; flip it. Check the 220 Ω resistor is in series.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
8 parts: Nano CH340 Development Board (Soldered), DS3231 Precision RTC Module with EEPROM, Tactile Push Button Switch, Active Buzzer Module 3.3–5V, Through-Hole LED Pack (Pack of 10), Resistor Assortment Kit (30 Values), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 1–2 hours. The build on this page has 10 steps.
No. This page has the complete, tested code (medicine_reminder_rtc.ino). Install this library first: RTClib.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹459 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Active vs passive buzzers; Current-limiting resistors for LEDs; Pull-ups and debouncing; Real-time clocks and backup batteries.
A reminder aid only. Follow the instructions of the doctor or pharmacist.
Ideas that reuse this build: RTC alarm clock and Pet feeder on a schedule. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.