Raspberry Pi Pico weather display (MicroPython)
Your first MicroPython project: temperature and humidity on an OLED.
Shop by category
Shop all componentsOne station on the classroom windowsill gives every class real data to work with: how the room warms through the day, how pressure falls before rain, when the UV peaks and how loud each period gets. Every minute it writes one row to a CSV file with the date and time, ready for a spreadsheet.
Tick anything you already have and the total updates.
Measures air temperature (±0.5 °C) and relative humidity (±2–5 %) on a single data wire.
Measures barometric pressure (±1 hPa) and temperature over I²C.
Temperature-compensated real-time clock (±2 minutes a year) with a coin-cell backup, so the time survives power cuts.
Stores readings on a microSD card as a CSV file you can open in Excel or Google Sheets.
Follow the colours: red is power, dark grey is ground, blue is a signal.
mega_classroom_science_station.inoVerify & upload in Electrolark// Classroom science data station on an Arduino Mega
// Geekobot project library · board: Arduino Mega 2560
// Wiring diagram, parts list and build steps: Geekobot project page "mega-classroom-science-station"
#include <DHT.h>
#include <Wire.h>
#include <Adafruit_BMP280.h>
#include <RTClib.h>
#include <SPI.h>
#include <SD.h>
// ---- pins ----
const uint8_t DHT_PIN = 22;
const uint8_t UV_PIN = A0;
const uint8_t MIC_PIN = A1;
const uint8_t SD_CS = 53;
const int ADC_MAX = 1023; // 10-bit analog input
const float VREF = 5.0f;
DHT dht(DHT_PIN, DHT22);
Adafruit_BMP280 bmp;
RTC_DS3231 rtc;
// ---- latest readings ----
float tempC = 0;
float humidity = 0;
float pressHpa = 0;
float bmpC = 0;
float uvIndex = 0;
int soundPct = 0;
const unsigned long LOG_EVERY_MS = 60000UL; // one row per minute
unsigned long lastLog = 0;
bool cardOk = false;
int readSoundLevel() {
// peak-to-peak amplitude over a 50 ms window
unsigned long start = millis();
int lo = ADC_MAX, hi = 0;
while (millis() - start < 50) {
int v = analogRead(MIC_PIN);
if (v < lo) lo = v;
if (v > hi) hi = v;
}
return (int)((hi - lo) * 100L / ADC_MAX);
}
void writeRow() {
File f = SD.open("LOG.CSV", FILE_WRITE);
if (!f) { Serial.println(F("Write failed")); return; }
DateTime t = rtc.now();
char stamp[20];
snprintf(stamp, sizeof(stamp), "%04d-%02d-%02d,%02d:%02d:%02d", t.year(), t.month(), t.day(), t.hour(), t.minute(), t.second());
f.print(stamp);
f.print(',');
f.print(tempC, 1);
f.print(',');
f.print(humidity, 0);
f.print(',');
f.print(pressHpa, 1);
f.print(',');
f.print(bmpC, 1);
f.print(',');
f.print(uvIndex, 1);
f.print(',');
f.print(soundPct);
f.println();
f.close();
}
void setup() {
Serial.begin(115200);
dht.begin();
if (!bmp.begin(0x76) && !bmp.begin(0x77)) Serial.println(F("BMP280 not found"));
if (!rtc.begin()) Serial.println(F("RTC not found"));
if (rtc.lostPower()) rtc.adjust(DateTime(F(__DATE__), F(__TIME__))); // set from the upload time
cardOk = SD.begin(SD_CS);
Serial.println(cardOk ? F("SD card ready") : F("SD card not found"));
if (cardOk && !SD.exists("LOG.CSV")) {
File f = SD.open("LOG.CSV", FILE_WRITE);
if (f) { f.println(F("date,time,Temp(C),Humidity(%),Pressure(hPa),Temp(C),UV index,Sound(%)")); f.close(); }
}
}
void loop() {
if (millis() - lastLog < LOG_EVERY_MS && lastLog != 0) return;
lastLog = millis();
tempC = dht.readTemperature();
humidity = dht.readHumidity();
pressHpa = bmp.readPressure() / 100.0f;
bmpC = bmp.readTemperature();
uvIndex = analogRead(UV_PIN) * VREF / ADC_MAX / 0.1f;
soundPct = readSoundLevel();
Serial.print(F("Temp="));
Serial.print(tempC, 1);
Serial.print(F("C"));
Serial.print(F(", Humidity="));
Serial.print(humidity, 0);
Serial.print(F("%"));
Serial.print(F(", Pressure="));
Serial.print(pressHpa, 1);
Serial.print(F("hPa"));
Serial.print(F(", Temp="));
Serial.print(bmpC, 1);
Serial.print(F("C"));
Serial.print(F(", UV index="));
Serial.print(uvIndex, 1);
Serial.print(F(", Sound="));
Serial.print(soundPct);
Serial.print(F("%"));
Serial.println();
if (cardOk) writeRow();
}
The sketch above runs here on a simulated Arduino Mega. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Check the DATA wire and the pull-up. The DHT22 needs at least 2 seconds between reads, so do not poll it faster.
Check SDA/SCL are not swapped. Run an I²C scanner sketch to confirm the address.
Expected. Take it outside in daylight.
Turn the module trimmer to increase gain, or move the mic closer to the sound.
The coin cell is flat or missing. Some modules need the charging resistor removed when using a CR2032.
Check the card is FAT32, fully inserted, and CS is on the pin in the sketch.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Use a 5 V USB phone charger or a power bank into the board's USB port.
10 parts: MEGA 2560 R3 Dev Board with ATmega2560 & CH340G, DHT22 Temperature & Humidity Sensor, BMP280 Temperature & Barometric Pressure Sensor Module, GUVA-S12SD UV Sensor Module, Analog Sound Sensor Microphone Module, DS3231 Precision RTC Module with EEPROM, DFRobot Fermion MicroSD Card Module – SPI, microSD Memory Card Class 10 (16GB), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 2–3 hours. The build on this page has 12 steps.
No. This page has the complete, tested code (mega_classroom_science_station.ino). Install these libraries first: DHT sensor library, Adafruit Unified Sensor, Adafruit BMP280 Library, RTClib and SD.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹2,611 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Converting a voltage to a physical unit; Real-time clocks and backup batteries; SPI devices and CSV logging; Sampling a waveform and measuring amplitude; Single-wire digital sensors and why some sensors need slow polling.
Ideas that reuse this build: Weather data logger and Classroom noise meter. They are listed under Take it further on this page.
Your first MicroPython project: temperature and humidity on an OLED.
A web page with ON and OFF buttons that switches a relay over Wi-Fi.
A warm ring light that fades up at dusk and down at dawn.
Turn a Pi and a touchscreen into a home command centre with a clock and to-do list.
Learning project. Check every circuit and the datasheet of each part before you power it up.
SD card ready Temp=26.9C, Humidity=55%, Pressure=1008.0hPa, Temp=26.0C, UV index=15.1, Sound=10% Temp=27.0C, Humidity=55%, Pressure=1007.9hPa, Temp=26.0C, UV index=15.0, Sound=10%
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.