LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsThe LD2410 sees people who sit still, the RCWL sees movement, and the light sensor shows lux. Comparing the three is a good way to learn what each sensor can and cannot do.
A learning and comparison aid, not a certified instrument.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Millimetre-wave radar that detects whether a person is in the room, even if they sit completely still, which a PIR sensor cannot do.
Microwave radar that senses movement through thin walls, glass and plastic, without needing body heat like a PIR sensor.
Digital light sensor that reports brightness in lux, the same unit used for room and street lighting.
Follow the colours: red is power, dark grey is ground, blue is a signal.
motion_and_light_room_board.inoVerify & upload in Electrolark// Room motion and light board
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "motion-and-light-room-board"
#include <Wire.h>
#include <BH1750.h>
#include <Adafruit_GFX.h>
#include <Adafruit_SSD1306.h>
// ---- pins ----
const uint8_t PRESENCE_PIN = 2;
const uint8_t RADAR_PIN = 3;
BH1750 lightMeter;
Adafruit_SSD1306 oled(128, 64, &Wire, -1);
// ---- latest readings ----
bool presence = false;
bool motion = false;
float lux = 0;
const unsigned long READ_EVERY_MS = 500;
unsigned long lastRead = 0;
const char* statusText = "OK";
void updateDisplay() {
oled.clearDisplay();
oled.setTextSize(1);
oled.setCursor(0, 0);
oled.print(F("Room"));
oled.drawLine(0, 10, 127, 10, SSD1306_WHITE);
oled.setCursor(0, 14);
oled.print(F("Presence: "));
oled.print(presence ? F("YES") : F("no"));
oled.setCursor(0, 24);
oled.print(F("Motion: "));
oled.print(motion ? F("YES") : F("no"));
oled.setCursor(0, 34);
oled.print(F("Light: "));
oled.print(lux, 0);
oled.print(F(" lx"));
oled.setCursor(0, 56);
oled.print(statusText);
oled.display();
}
void setup() {
Serial.begin(115200);
pinMode(PRESENCE_PIN, INPUT);
pinMode(RADAR_PIN, INPUT);
Wire.begin();
if (!lightMeter.begin()) Serial.println(F("BH1750 not found"));
if (!oled.begin(SSD1306_SWITCHCAPVCC, 0x3C)) Serial.println(F("OLED not found"));
oled.setTextColor(SSD1306_WHITE);
oled.clearDisplay();
oled.display();
}
void loop() {
if (millis() - lastRead < READ_EVERY_MS) return;
lastRead = millis();
presence = digitalRead(PRESENCE_PIN) == HIGH;
motion = digitalRead(RADAR_PIN) == HIGH;
lux = lightMeter.readLightLevel();
statusText = (lux >= 0) ? "OK" : "Sensor error";
Serial.print(F("Presence="));
Serial.print(presence ? F("yes") : F("no"));
Serial.print(F(", Motion="));
Serial.print(motion ? F("yes") : F("no"));
Serial.print(F(", Light="));
Serial.print(lux, 0);
Serial.print(F("lx"));
Serial.println();
updateDisplay();
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Move the sensor away from fans, moving curtains and metal that vibrates, and give it a minute to settle.
Check it has 5 V on VCC and the OUT wire goes to the right pin.
Move it away from motors, fluorescent lights and switching power supplies, and give it a minute to settle.
Check the module has about 5 V on VIN. The output stays high for roughly two seconds after each movement.
Check SDA and SCL are not swapped. An I²C scanner should show 0x23 (0x5C if the ADDR pin is tied high).
Check the wiring and power, then try again. A reading of 0 in a dark room is normal.
Check SDA/SCL and try address 0x3D. Run an I²C scanner to confirm.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
7 parts: Nano CH340 Development Board (Soldered), HLK-LD2410 24GHz Human Presence Radar Sensor Module – 5 m Range, RCWL-0516 Microwave Radar Motion Sensor Module, GY-302 BH1750 Light Intensity Module – I2C Interface, 0.96" OLED Display 128x64 (I2C), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 2–3 hours. The build on this page has 10 steps.
No. This page has the complete, tested code (motion_and_light_room_board.ino). Install these libraries first: BH1750, Adafruit SSD1306 and Adafruit GFX Library.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹946 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Doppler radar and motion sensing; Drawing text on an I²C display; Lux, lumens and the I²C bus; Radar presence sensing.
A learning and comparison aid, not a certified instrument.
Ideas that reuse this build: Wi-Fi meeting room occupied sign and Wi-Fi motion light with override. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Presence=no, Motion=no, Light=319lx Presence=no, Motion=no, Light=319lx Presence=no, Motion=no, Light=320lx Presence=no, Motion=no, Light=320lx Presence=no, Motion=no, Light=321lx
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.