LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsA running toilet cistern or a tap left open overnight can empty the tank by morning. The flow sensor on the tank outlet and a light sensor work together: when the house is dark and water keeps flowing, the buzzer and red light wake someone up to check.
Every main part of this project is an item on the public Package 1 equipment list, so a school lab that already owns Package 1 can build it without buying anything extra.
See the full Atal Tinkering Lab packages →
Geekobot is an independent shop, not endorsed by or affiliated with NITI Aayog or the Atal Innovation Mission. Item names follow the public AIM equipment list.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
A small turbine with a magnet and Hall sensor: each turn sends a pulse, and pulses per second give the flow rate.
Light-dependent resistor with a comparator: its output flips when the light falls below the level set by the trimmer.
Active buzzer with a built-in oscillator: apply power and it beeps at about 2.3 kHz.
Follow the colours: red is power, dark grey is ground, blue is a signal.
night_water_leak_flow_alarm.inoVerify & upload in Electrolark// Night-time water leak alarm
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "night-water-leak-flow-alarm"
#if defined(ESP32) || defined(ESP8266)
#define IRAM_SAFE IRAM_ATTR
#else
#define IRAM_SAFE
#endif
// ---- pins ----
const uint8_t FLOW_PIN = 2;
const uint8_t LDR_PIN = 3;
const uint8_t BUZZER_PIN = 4;
const uint8_t LED_RED = 5;
volatile unsigned long flowPulses = 0;
unsigned long lastFlowMs = 0;
float litresTotal = 0;
// ---- latest readings ----
float flowLpm = 0;
float litres = 0;
bool dark = false;
const unsigned long READ_EVERY_MS = 1000;
unsigned long lastRead = 0;
bool alertOn = false;
const char* statusText = "Starting";
const float ALERT_LEVEL = 0.3; // at night nobody should be using water, so steady flow means a leak or an open tap
const float HYSTERESIS = 0.2; // gap that stops rapid on/off switching
const unsigned long HOLD_MS = 600000; // keep the alert on this long after the last trigger
unsigned long lastTrigger = 0;
bool levelHigh = false;
void IRAM_SAFE onFlowPulse() { flowPulses++; }
float readFlowLpm() {
unsigned long now = millis();
float secs = (now - lastFlowMs) / 1000.0f;
if (secs <= 0) return 0;
noInterrupts();
unsigned long p = flowPulses;
flowPulses = 0;
interrupts();
lastFlowMs = now;
float lpm = (p / secs) / 7.5f; // YF-S201: about 7.5 pulses per second per L/min
litresTotal += lpm * secs / 60.0f;
return lpm;
}
void setBuzzer(bool on) { digitalWrite(BUZZER_PIN, on ? HIGH : LOW); }
void setRedLed(bool on) { digitalWrite(LED_RED, on ? HIGH : LOW); }
void evaluate() {
if (!levelHigh && flowLpm > ALERT_LEVEL) levelHigh = true;
else if (levelHigh && flowLpm < ALERT_LEVEL - HYSTERESIS) levelHigh = false;
if (levelHigh && dark) lastTrigger = millis();
alertOn = lastTrigger != 0 && millis() - lastTrigger < HOLD_MS;
statusText = alertOn ? "WATER RUNNING AT NIGHT" : "OK";
}
void setup() {
Serial.begin(115200);
pinMode(FLOW_PIN, INPUT_PULLUP);
attachInterrupt(digitalPinToInterrupt(FLOW_PIN), onFlowPulse, RISING);
lastFlowMs = millis();
pinMode(LDR_PIN, INPUT);
pinMode(BUZZER_PIN, OUTPUT);
setBuzzer(false);
pinMode(LED_RED, OUTPUT);
}
void loop() {
if (millis() - lastRead >= READ_EVERY_MS) {
lastRead = millis();
flowLpm = readFlowLpm();
litres = litresTotal;
dark = digitalRead(LDR_PIN) == HIGH;
evaluate();
Serial.print(F("Flow="));
Serial.print(flowLpm, 1);
Serial.print(F("L/min"));
Serial.print(F(", Total="));
Serial.print(litres, 2);
Serial.print(F("L"));
Serial.print(F(", Dark="));
Serial.print(dark ? F("yes") : F("no"));
Serial.print(F(", status=")); Serial.println(statusText);
}
setBuzzer(alertOn && (millis() / 250) % 2 == 0); // intermittent beep
setRedLed(alertOn && (millis() / 250) % 2 == 0);
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Check the arrow direction and that the signal wire is on an interrupt-capable pin.
Some modules invert DO. Change == HIGH to == LOW in the code.
Low-triggered module: invert the logic in setBuzzer().
LED is reversed; flip it. Check the 220 Ω resistor is in series.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
It stops the output flickering on and off when the reading hovers right at the limit. The output switches on at ALERT_LEVEL and only switches off once the reading has moved back by the hysteresis amount.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
8 parts: Nano CH340 Development Board (Soldered), YF-S201 Water Flow Sensor 1–30 L/min, Digital LDR Light Sensor Module – LM393, Active Buzzer Module 3.3–5V, Through-Hole LED Pack (Pack of 10), Resistor Assortment Kit (30 Values), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 2 hours. The build on this page has 10 steps.
No. This page has the complete, tested code (night_water_leak_flow_alarm.ino).
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹545 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Active vs passive buzzers; Current-limiting resistors for LEDs; Interrupts and counting pulses; Thresholds set in hardware vs software.
Ideas that reuse this build: Tap left running alarm and Water leak alarm. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Flow=0.0L/min, Total=0.00L, Dark=no, status=OK Flow=0.0L/min, Total=0.00L, Dark=no, status=OK
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.