LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsSpices dry best in warm, dry air. The AHT10 near the trays shows both on the OLED, so you know when the room is too damp to dry well and when to run a fan or move the trays into the sun.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Small digital sensor for air temperature (±0.3 °C) and humidity (±2 %) over I²C, more accurate than the common DHT11.
Follow the colours: red is power, dark grey is ground, blue is a signal.
papad_drying_room_monitor.inoVerify & upload in Electrolark// Papad and spice drying room monitor
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "papad-drying-room-monitor"
#include <Wire.h>
#include <Adafruit_AHTX0.h>
#include <Adafruit_GFX.h>
#include <Adafruit_SSD1306.h>
Adafruit_AHTX0 aht;
sensors_event_t ahtH, ahtT;
Adafruit_SSD1306 oled(128, 64, &Wire, -1);
// ---- latest readings ----
float tempC = 0;
float humidity = 0;
const unsigned long READ_EVERY_MS = 2000;
unsigned long lastRead = 0;
const char* statusText = "OK";
void readAht() { aht.getEvent(&ahtH, &ahtT); }
void updateDisplay() {
oled.clearDisplay();
oled.setTextSize(1);
oled.setCursor(0, 0);
oled.print(F("Drying room"));
oled.drawLine(0, 10, 127, 10, SSD1306_WHITE);
oled.setCursor(0, 14);
oled.print(F("Temp: "));
oled.print(tempC, 1);
oled.print(F(" C"));
oled.setCursor(0, 24);
oled.print(F("Humidity: "));
oled.print(humidity, 0);
oled.print(F("%"));
oled.setCursor(0, 56);
oled.print(statusText);
oled.display();
}
void setup() {
Serial.begin(115200);
if (!aht.begin()) Serial.println(F("AHT10 not found"));
if (!oled.begin(SSD1306_SWITCHCAPVCC, 0x3C)) Serial.println(F("OLED not found"));
oled.setTextColor(SSD1306_WHITE);
oled.clearDisplay();
oled.display();
}
void loop() {
if (millis() - lastRead < READ_EVERY_MS) return;
lastRead = millis();
tempC = (readAht(), ahtT.temperature);
humidity = ahtH.relative_humidity;
statusText = (!isnan(tempC) && !isnan(humidity)) ? "OK" : "Sensor error";
Serial.print(F("Temp="));
Serial.print(tempC, 1);
Serial.print(F("C"));
Serial.print(F(", Humidity="));
Serial.print(humidity, 0);
Serial.print(F("%"));
Serial.println();
updateDisplay();
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Check SDA and SCL are not swapped and that the module has 3.3 V or 5 V. An I²C scanner should show 0x38.
Moisture has condensed on the sensor. Dry it in warm air for an hour and keep it out of direct spray.
Check SDA/SCL and try address 0x3D. Run an I²C scanner to confirm.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
5 parts: Nano CH340 Development Board (Soldered), AHT10 High Precision Digital Temperature & Humidity Sensor Module – I2C Interface, 0.96" OLED Display 128x64 (I2C), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1 hour. The build on this page has 8 steps.
No. This page has the complete, tested code (papad_drying_room_monitor.ino). Install these libraries first: Adafruit AHTX0, Adafruit SSD1306 and Adafruit GFX Library.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹503 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Digital sensors and accuracy versus price; Drawing text on an I²C display.
Ideas that reuse this build: Pickle and papad sun-drying monitor and AHT10 room climate monitor. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Temp=25.9C, Humidity=55%
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.