LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsDies need sharpening after a set number of hits, and job cards need a count. A magnet on the ram passes the reed switch once per stroke; the display shows the job count and the Nano keeps the lifetime total in memory through power cuts. The button clears the job count only.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Glass switch whose contacts close when a magnet is near.
Bright 4-digit 7-segment display driven by two wires.
Follow the colours: red is power, dark grey is ground, blue is a signal.
press_stroke_counter.inoVerify & upload in Electrolark// Press and punch stroke counter
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "press-stroke-counter"
#include <TM1637Display.h>
#include <EEPROM.h>
// ---- pins ----
const uint8_t REED_PIN = 2;
const uint8_t SEG_CLK = 3;
const uint8_t SEG_DIO = 4;
const uint8_t BUTTON_PIN = 5;
TM1637Display seg(SEG_CLK, SEG_DIO);
// ---- latest readings ----
bool doorOpen = false;
unsigned long total = 0; // lifetime strokes, saved in EEPROM
unsigned int job = 0; // strokes in this job, shown on the display
bool wasClosed = false;
unsigned long lastStroke = 0;
void setup() {
Serial.begin(115200);
pinMode(REED_PIN, INPUT_PULLUP);
seg.setBrightness(5);
seg.clear();
pinMode(BUTTON_PIN, INPUT_PULLUP);
EEPROM.get(0, total);
if (total == 0xFFFFFFFFUL) total = 0;
seg.showNumberDec(0);
}
void loop() {
bool closed = digitalRead(REED_PIN) == LOW; // magnet on the ram passes the switch once per stroke
if (closed && !wasClosed && millis() - lastStroke > 150) {
lastStroke = millis(); job++; total++;
seg.showNumberDec(job % 10000);
if (total % 50 == 0) EEPROM.put(0, total); // save every 50 strokes
Serial.print(F("job ")); Serial.print(job); Serial.print(F(", total ")); Serial.println(total);
}
wasClosed = closed;
if (digitalRead(BUTTON_PIN) == LOW) { job = 0; seg.showNumberDec(0); EEPROM.put(0, total); delay(400); }
delay(2);
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Bring the magnet within 1 cm and align it parallel to the glass body.
CLK and DIO swapped; swap them.
The button is rotated 90°; legs on the same side are already connected. Turn it.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
6 parts: Nano CH340 Development Board (Soldered), Y213 Reed Switch Normally Open (glass), TM1637 4-Digit 7-Segment Display Module, Tactile Push Button Switch, Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1 hour. The build on this page has 9 steps.
No. This page has the complete, tested code (press_stroke_counter.ino). Install this library first: TM1637.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹337 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Multiplexed 7-segment displays; Pull-up resistors and reed switches; Pull-ups and debouncing.
Ideas that reuse this build: Conveyor batch counter and Machine hour meter. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.