LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsA pump that is running hot, shaking or moving less water than it used to is trying to tell you something. This logger writes all four signals every 15 seconds so you can compare today with last month.
Mount the Nano box away from water and mains wiring.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Spring-type vibration switch with a comparator: the output goes high while it is being shaken.
Waterproof stainless-steel probe that reads liquid or soil temperature from −55 to +125 °C (±0.5 °C).
A small turbine with a magnet and Hall sensor: each turn sends a pulse, and pulses per second give the flow rate.
A sealed float with a switch inside.
Temperature-compensated real-time clock (±2 minutes a year) with a coin-cell backup, so the time survives power cuts.
Stores readings on a microSD card as a CSV file you can open in Excel or Google Sheets.
Follow the colours: red is power, dark grey is ground, blue is a signal.
pump_house_health_logger.inoVerify & upload in Electrolark// Pump house health logger
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "pump-house-health-logger"
#include <OneWire.h>
#include <DallasTemperature.h>
#include <Wire.h>
#include <RTClib.h>
#include <SPI.h>
#include <SD.h>
#if defined(ESP32) || defined(ESP8266)
#define IRAM_SAFE IRAM_ATTR
#else
#define IRAM_SAFE
#endif
// ---- pins ----
const uint8_t VIB_PIN = 3;
const uint8_t ONEWIRE_PIN = 4;
const uint8_t FLOW_PIN = 2;
const uint8_t FLOAT_PIN = 5;
const uint8_t SD_CS = 10;
OneWire oneWire(ONEWIRE_PIN);
DallasTemperature probes(&oneWire);
volatile unsigned long flowPulses = 0;
unsigned long lastFlowMs = 0;
float litresTotal = 0;
RTC_DS3231 rtc;
// ---- latest readings ----
bool shake = false;
float probeC = 0;
float flowLpm = 0;
float litres = 0;
bool floatUp = false;
const unsigned long LOG_EVERY_MS = 15000UL; // one row per 15 s
unsigned long lastLog = 0;
bool cardOk = false;
float readProbeC() {
probes.requestTemperatures();
return probes.getTempCByIndex(0);
}
void IRAM_SAFE onFlowPulse() { flowPulses++; }
float readFlowLpm() {
unsigned long now = millis();
float secs = (now - lastFlowMs) / 1000.0f;
if (secs <= 0) return 0;
noInterrupts();
unsigned long p = flowPulses;
flowPulses = 0;
interrupts();
lastFlowMs = now;
float lpm = (p / secs) / 7.5f; // YF-S201: about 7.5 pulses per second per L/min
litresTotal += lpm * secs / 60.0f;
return lpm;
}
void writeRow() {
File f = SD.open("LOG.CSV", FILE_WRITE);
if (!f) { Serial.println(F("Write failed")); return; }
DateTime t = rtc.now();
char stamp[20];
snprintf(stamp, sizeof(stamp), "%04d-%02d-%02d,%02d:%02d:%02d", t.year(), t.month(), t.day(), t.hour(), t.minute(), t.second());
f.print(stamp);
f.print(',');
f.print(shake);
f.print(',');
f.print(probeC, 1);
f.print(',');
f.print(flowLpm, 1);
f.print(',');
f.print(litres, 2);
f.print(',');
f.print(floatUp);
f.println();
f.close();
}
void setup() {
Serial.begin(115200);
pinMode(VIB_PIN, INPUT);
probes.begin();
pinMode(FLOW_PIN, INPUT_PULLUP);
attachInterrupt(digitalPinToInterrupt(FLOW_PIN), onFlowPulse, RISING);
lastFlowMs = millis();
pinMode(FLOAT_PIN, INPUT_PULLUP);
if (!rtc.begin()) Serial.println(F("RTC not found"));
if (rtc.lostPower()) rtc.adjust(DateTime(F(__DATE__), F(__TIME__))); // set from the upload time
cardOk = SD.begin(SD_CS);
Serial.println(cardOk ? F("SD card ready") : F("SD card not found"));
if (cardOk && !SD.exists("LOG.CSV")) {
File f = SD.open("LOG.CSV", FILE_WRITE);
if (f) { f.println(F("date,time,Vibration,Probe(C),Flow(L/min),Total(L),Float up")); f.close(); }
}
}
void loop() {
if (millis() - lastLog < LOG_EVERY_MS && lastLog != 0) return;
lastLog = millis();
shake = digitalRead(VIB_PIN) == HIGH;
probeC = readProbeC();
flowLpm = readFlowLpm();
litres = litresTotal;
floatUp = digitalRead(FLOAT_PIN) == LOW;
Serial.print(F("Vibration="));
Serial.print(shake ? F("yes") : F("no"));
Serial.print(F(", Probe="));
Serial.print(probeC, 1);
Serial.print(F("C"));
Serial.print(F(", Flow="));
Serial.print(flowLpm, 1);
Serial.print(F("L/min"));
Serial.print(F(", Total="));
Serial.print(litres, 2);
Serial.print(F("L"));
Serial.print(F(", Float up="));
Serial.print(floatUp ? F("yes") : F("no"));
Serial.println();
if (cardOk) writeRow();
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Turn the trimmer and tap harder; loosely mounted modules absorb vibration.
The 4.7 kΩ pull-up is missing or DATA is on the wrong pin. Check the yellow wire.
Check the arrow direction and that the signal wire is on an interrupt-capable pin.
Flip the float over (the arrow or marking points up) or swap the logic in the sketch.
Clear any dirt or sludge from around the float so it moves freely.
The coin cell is flat or missing. Some modules need the charging resistor removed when using a CR2032.
Check the card is FAT32, fully inserted, and CS is on the pin in the sketch.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
11 parts: Nano CH340 Development Board (Soldered), SW-420 Vibration Sensor Module – Digital Output, DS18B20 Waterproof Temperature Probe – 1m Cable, YF-S201 Water Flow Sensor 1–30 L/min, Square Float Switch, 2 m Cable, IP68 – Pump Tank Level Sensor, DS3231 Precision RTC Module with EEPROM, DFRobot Fermion MicroSD Card Module – SPI, Resistor Assortment Kit (30 Values), microSD Memory Card Class 10 (16GB), Solderless Breadboard (830 points), plus 1 more. Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a advanced project and takes about 4–5 hours. The build on this page has 12 steps.
No. This page has the complete, tested code (pump_house_health_logger.ino). Install these libraries first: OneWire, DallasTemperature, RTClib and SD.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹1,839 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
1-Wire bus and pull-up resistors; Debouncing noisy digital signals; Interrupts and counting pulses; Level switches and pull-up resistors; Real-time clocks and backup batteries.
Mount the Nano box away from water and mains wiring.
Ideas that reuse this build: Wi-Fi sump and tank float monitor and Water flow meter. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
SD card ready Vibration=yes, Probe=26.0C, Flow=0.0L/min, Total=0.00L, Float up=no Vibration=yes, Probe=26.0C, Flow=0.0L/min, Total=0.00L, Float up=no
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.