Remote-controlled RGB mood light
Warm, cool, rainbow or breathing: cycle lighting moods from your sofa.
Shop by category
Shop all componentsAfter a random wait, the green light comes on with a beep. Player 1 presses button 1 and player 2 presses button 3: the first one wins, and the Serial Monitor shows the time in milliseconds. Jump the gun and the red light flashes your false start.
Every main part of this project is an item on the public Package 1 equipment list, so a school lab that already owns Package 1 can build it without buying anything extra.
See the full Atal Tinkering Lab packages →
Geekobot is an independent shop, not endorsed by or affiliated with NITI Aayog or the Atal Innovation Mission. Item names follow the public AIM equipment list.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Three momentary buttons, one leg each to a pin and the other legs joined to GND; the internal pull-ups do the rest.
Green indicator LED for the normal state.; Red indicator LED for the alert state.
Active buzzer with a built-in oscillator: apply power and it beeps at about 2.3 kHz.
Follow the colours: red is power, dark grey is ground, blue is a signal.
reaction_duel_two_players.inoVerify & upload in Electrolark// Two-player reaction duel
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "reaction-duel-two-players"
// ---- pins ----
const uint8_t BTN_1 = 2;
const uint8_t BTN_2 = 3;
const uint8_t BTN_3 = 4;
const uint8_t LED_GREEN = 5;
const uint8_t LED_RED = 6;
const uint8_t BUZZER_PIN = 7;
const int ADC_MAX = 1023; // 10-bit analog input
const float VREF = 5.0f;
// returns 0 when nothing is pressed, else 1-3
int pressedButton() {
if (digitalRead(BTN_1) == LOW) return 1;
if (digitalRead(BTN_2) == LOW) return 2;
if (digitalRead(BTN_3) == LOW) return 3;
return 0;
}
void setGreenLed(bool on) { digitalWrite(LED_GREEN, on ? HIGH : LOW); }
void setRedLed(bool on) { digitalWrite(LED_RED, on ? HIGH : LOW); }
void setBuzzer(bool on) { digitalWrite(BUZZER_PIN, on ? HIGH : LOW); }
void setup() {
Serial.begin(115200);
pinMode(BTN_1, INPUT_PULLUP); pinMode(BTN_2, INPUT_PULLUP); pinMode(BTN_3, INPUT_PULLUP);
pinMode(LED_GREEN, OUTPUT);
pinMode(LED_RED, OUTPUT);
pinMode(BUZZER_PIN, OUTPUT);
setBuzzer(false);
randomSeed(analogRead(A0));
}
void loop() {
Serial.println(F("Get ready..."));
setGreenLed(false);
unsigned long go = millis() + random(2000, 6000);
while (millis() < go) {
int p = pressedButton();
if (p == 1 || p == 3) { // pressed too early: that player loses
Serial.print(F("False start by player ")); Serial.println(p == 1 ? 1 : 2);
for (int i = 0; i < 3; i++) { setRedLed(true); delay(150); setRedLed(false); delay(150); }
delay(1500); return;
}
}
setGreenLed(true); setBuzzer(true); delay(40); setBuzzer(false);
unsigned long t0 = millis();
int p = 0;
while (p != 1 && p != 3) p = pressedButton();
Serial.print(F("Player ")); Serial.print(p == 1 ? 1 : 2); Serial.print(F(" wins in ")); Serial.print(millis() - t0); Serial.println(F(" ms"));
for (int i = 0; i < p; i++) { setBuzzer(true); delay(120); setBuzzer(false); delay(120); } // one beep for player 1, three for player 2
delay(2000);
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
It is rotated 90°; turn it so the legs span the gap.
LED is reversed; flip it. Check the 220 Ω resistor is in series.
Low-triggered module: invert the logic in setBuzzer().
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
7 parts: Nano CH340 Development Board (Soldered), 3 × Tactile Push Button Switch, 2 × Through-Hole LED Pack (Pack of 10), Active Buzzer Module 3.3–5V, Resistor Assortment Kit (30 Values), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1–2 hours. The build on this page has 9 steps.
No. This page has the complete, tested code (reaction_duel_two_players.ino).
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹363 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Active vs passive buzzers; Current-limiting resistors for LEDs; Pull-ups and debouncing.
Ideas that reuse this build: Reaction timer and Tug of war. They are listed under Take it further on this page.
Warm, cool, rainbow or breathing: cycle lighting moods from your sofa.
Press to roll: the pips tumble and slow down before landing on a number.
Wait for the light, hit the button: how many milliseconds can you beat?
A bright 4-digit clock that keeps time through power cuts.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Get ready...
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.