Remote-controlled RGB mood light
Warm, cool, rainbow or breathing: cycle lighting moods from your sofa.
Shop by category
Shop all componentsGet up at night and the light comes on by itself: the sound sensor hears your footsteps, the LDR confirms the room is dark, and the ring glows a warm orange for twenty seconds, long enough to find the door. It stays off during the day however loud it gets.
Tick anything you already have and the total updates.
Sixteen individually addressable RGB LEDs on one data wire.
Light-dependent resistor with a comparator: its output flips when the light falls below the level set by the trimmer.
Follow the colours: red is power, dark grey is ground, blue is a signal.
sleep_light_nightlight.inoVerify & upload in Electrolark// Sound-activated night light
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "sleep-light-nightlight"
#include <Adafruit_NeoPixel.h>
// ---- pins ----
const uint8_t MIC_PIN = A0;
const uint8_t RING_PIN = 2;
const uint8_t LDR_PIN = 3;
const int ADC_MAX = 1023; // 10-bit analog input
const float VREF = 5.0f;
const int RING_LEDS = 16;
Adafruit_NeoPixel ring(RING_LEDS, RING_PIN, NEO_GRB + NEO_KHZ800);
// ---- latest readings ----
int soundPct = 0;
bool dark = false;
const int SOUND_LEVEL = 25; // Sound % that counts as a footstep or a cough
const unsigned long ON_MS = 20000; // stay lit this long after the last sound
unsigned long lastHeard = 0;
int glow = 0; // current brightness, faded smoothly
int readSoundLevel() {
// peak-to-peak amplitude over a 50 ms window
unsigned long start = millis();
int lo = ADC_MAX, hi = 0;
while (millis() - start < 50) {
int v = analogRead(MIC_PIN);
if (v < lo) lo = v;
if (v > hi) hi = v;
}
return (int)((hi - lo) * 100L / ADC_MAX);
}
void showLevel(int pct, uint32_t color) {
int lit = constrain(pct, 0, 100) * RING_LEDS / 100;
for (int i = 0; i < RING_LEDS; i++) ring.setPixelColor(i, i < lit ? color : 0);
ring.show();
}
void paint(int level) {
for (int i = 0; i < RING_LEDS; i++) ring.setPixelColor(i, ring.Color(level, level * 2 / 5, level / 12)); // warm orange
ring.show();
}
void setup() {
Serial.begin(115200);
ring.begin();
ring.setBrightness(40);
ring.show();
pinMode(LDR_PIN, INPUT);
}
void loop() {
soundPct = readSoundLevel();
dark = digitalRead(LDR_PIN) == HIGH;
if (dark && soundPct > SOUND_LEVEL) lastHeard = millis();
int target = (lastHeard && millis() - lastHeard < ON_MS) ? 160 : 0;
if (glow < target) glow += 4; else if (glow > target) glow -= 2; // fade up quickly, down slowly
glow = constrain(glow, 0, 160);
paint(glow);
if (soundPct > SOUND_LEVEL) { Serial.print(F("Sound ")); Serial.print(soundPct); Serial.println(dark ? F("% (dark: light on)") : F("% (daylight: ignored)")); }
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Turn the module trimmer to increase gain, or move the mic closer to the sound.
Add the 330 Ω resistor in series with DIN and share GND with the board.
Some modules invert DO. Change == HIGH to == LOW in the code.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider. Analog readings run 0–4095 instead of 0–1023, which the ADC_MAX constant handles.
Use a 5 V USB phone charger or a power bank into the board's USB port.
7 parts: Nano CH340 Development Board (Soldered), Analog Sound Sensor Microphone Module, WS2812 RGB LED Ring (16 LEDs), Digital LDR Light Sensor Module – LM393, Resistor Assortment Kit (30 Values), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1 hour. The build on this page has 9 steps.
No. This page has the complete, tested code (sleep_light_nightlight.ino). Install this library first: Adafruit NeoPixel.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹469 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Addressable LEDs and colour mixing; Sampling a waveform and measuring amplitude; Thresholds set in hardware vs software.
Ideas that reuse this build: Motion-activated version and Clap switch for a lamp. They are listed under Take it further on this page.
Warm, cool, rainbow or breathing: cycle lighting moods from your sofa.
Press to roll: the pips tumble and slow down before landing on a number.
Wait for the light, hit the button: how many milliseconds can you beat?
A bright 4-digit clock that keeps time through power cuts.
Learning project. Check every circuit and the datasheet of each part before you power it up.
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.