LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsIn India the best fixed direction for a solar panel is due south, which is 180 degrees on the compass. Lay the QMC5883L flat on the panel frame, away from steel, and the OLED shows the heading so you can rotate the frame until it reads close to 180.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Three-axis magnetometer: it feels the Earth's magnetic field and works out which way the board is pointing (0 to 359 degrees from north).
Follow the colours: red is power, dark grey is ground, blue is a signal.
solar_panel_south_aligner.inoVerify & upload in Electrolark// Solar panel south aligner
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "solar-panel-south-aligner"
#include <Wire.h>
#include <QMC5883LCompass.h>
#include <Adafruit_GFX.h>
#include <Adafruit_SSD1306.h>
QMC5883LCompass compass;
Adafruit_SSD1306 oled(128, 64, &Wire, -1);
// ---- latest readings ----
int headingDeg = 0;
const unsigned long READ_EVERY_MS = 200;
unsigned long lastRead = 0;
const char* statusText = "OK";
void updateDisplay() {
oled.clearDisplay();
oled.setTextSize(1);
oled.setCursor(0, 0);
oled.print(F("Panel facing"));
oled.drawLine(0, 10, 127, 10, SSD1306_WHITE);
oled.setCursor(0, 16);
oled.print(F("Heading"));
oled.setTextSize(2);
oled.setCursor(0, 28);
oled.print(headingDeg);
oled.print(F(" deg"));
oled.setTextSize(1);
oled.display();
}
void setup() {
Serial.begin(115200);
compass.init();
if (!oled.begin(SSD1306_SWITCHCAPVCC, 0x3C)) Serial.println(F("OLED not found"));
oled.setTextColor(SSD1306_WHITE);
oled.clearDisplay();
oled.display();
}
void loop() {
if (millis() - lastRead < READ_EVERY_MS) return;
lastRead = millis();
headingDeg = (compass.read(), compass.getAzimuth());
Serial.print(F("Heading="));
Serial.print(headingDeg);
Serial.print(F("deg"));
Serial.println();
updateDisplay();
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Magnetic north differs from true north by a few degrees in most places. Add or subtract your local declination.
Move the sensor at least 10 cm from motors, magnets and speaker magnets.
Check SDA/SCL and try address 0x3D. Run an I²C scanner to confirm.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
5 parts: Nano CH340 Development Board (Soldered), GY-271 QMC5883L 3-Axis Electronic Compass Module – I2C Interface, 0.96" OLED Display 128x64 (I2C), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1 hour. The build on this page has 8 steps.
No. This page has the complete, tested code (solar_panel_south_aligner.ino). Install these libraries first: QMC5883LCompass, Adafruit SSD1306 and Adafruit GFX Library.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹592 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Drawing text on an I²C display; Magnetometers and compass headings.
Ideas that reuse this build: Digital compass and Room and plot direction finder. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Heading=30deg Heading=30deg Heading=30deg Heading=30deg Heading=30deg Heading=30deg Heading=30deg Heading=30deg Heading=30deg
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.