Remote-controlled RGB mood light
Warm, cool, rainbow or breathing: cycle lighting moods from your sofa.
Shop by category
Shop all componentsDebates, elocution contests and meetings run over time because speakers cannot see a clock. Set the talk length on the knob (1 to 20 minutes) and press start. The light stays green, turns yellow two minutes before the end, and red with a beep at zero; after 30 seconds over, it flashes and the display counts the overrun.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
A 10 kΩ knob that works as a voltage divider, giving an analog value you can map to anything.
Three indicator LEDs, each through a 330 Ω resistor to its pin.
Bright 4-digit 7-segment display driven by two wires.
Active buzzer with a built-in oscillator: apply power and it beeps at about 2.3 kHz.
Follow the colours: red is power, dark grey is ground, blue is a signal.
speech_timer_traffic_lights.inoVerify & upload in Electrolark// Speech and debate timer with traffic lights
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "speech-timer-traffic-lights"
#include <TM1637Display.h>
// ---- pins ----
const uint8_t POT_PIN = A0;
const uint8_t BUTTON_PIN = 2;
const uint8_t LED_RED = 3;
const uint8_t LED_YELLOW = 4;
const uint8_t LED_GREEN = 5;
const uint8_t SEG_CLK = 6;
const uint8_t SEG_DIO = 7;
const uint8_t BUZZER_PIN = 8;
const int ADC_MAX = 1023; // 10-bit analog input
const float VREF = 5.0f;
TM1637Display seg(SEG_CLK, SEG_DIO);
// ---- latest readings ----
int potPct = 0;
const long WARN_SEC = 120; // yellow light for the last two minutes
long talkSec = 300, leftSec = 0;
bool running = false;
unsigned long lastTick = 0;
void setRedLed(bool on) { digitalWrite(LED_RED, on ? HIGH : LOW); }
void setYellowLed(bool on) { digitalWrite(LED_YELLOW, on ? HIGH : LOW); }
void setGreenLed(bool on) { digitalWrite(LED_GREEN, on ? HIGH : LOW); }
void setLed(int n, bool on) { if (n == 1) setRedLed(on); else if (n == 2) setYellowLed(on); else setGreenLed(on); }
void setBuzzer(bool on) { digitalWrite(BUZZER_PIN, on ? HIGH : LOW); }
void show(long sec) {
long s = sec < 0 ? -sec : sec; // after time is up it counts the overrun
seg.showNumberDecEx((s / 60) * 100 + s % 60, 0b01000000, true);
}
void setup() {
Serial.begin(115200);
pinMode(BUTTON_PIN, INPUT_PULLUP);
pinMode(LED_RED, OUTPUT); pinMode(LED_YELLOW, OUTPUT); pinMode(LED_GREEN, OUTPUT);
seg.setBrightness(5);
seg.clear();
pinMode(BUZZER_PIN, OUTPUT);
setBuzzer(false);
show(talkSec);
}
void loop() {
if (!running) {
long want = map(analogRead(POT_PIN), 0, ADC_MAX, 1, 20) * 60L; // knob sets 1 to 20 minutes
if (want != talkSec) { talkSec = want; show(talkSec); }
}
if (digitalRead(BUTTON_PIN) == LOW) {
running = !running;
if (running) { leftSec = talkSec; lastTick = millis(); }
else { setRedLed(false); setYellowLed(false); setGreenLed(false); show(talkSec); }
while (digitalRead(BUTTON_PIN) == LOW) delay(10);
}
if (!running) return;
if (millis() - lastTick >= 1000) {
lastTick += 1000; leftSec--; show(leftSec);
if (leftSec == 0) { setBuzzer(true); delay(400); setBuzzer(false); }
}
setGreenLed(leftSec > WARN_SEC);
setYellowLed(leftSec > 0 && leftSec <= WARN_SEC);
setRedLed(leftSec <= 0 && (leftSec > -30 || (millis() / 500) % 2 == 0)); // red, then flashing once over by 30 s
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
The wiper is on an outer pin. Move the signal wire to the middle leg.
The button is rotated 90°; legs on the same side are already connected. Turn it.
It is backwards: the long leg goes to the resistor.
CLK and DIO swapped; swap them.
Low-triggered module: invert the logic in setBuzzer().
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider. Analog readings run 0–4095 instead of 0–1023, which the ADC_MAX constant handles.
Use a 5 V USB phone charger or a power bank into the board's USB port.
9 parts: Nano CH340 Development Board (Soldered), 16mm Rotary Potentiometer 10kΩ (Linear), Tactile Push Button Switch, Through-Hole LED Pack (Pack of 10), TM1637 4-Digit 7-Segment Display Module, Active Buzzer Module 3.3–5V, Resistor Assortment Kit (30 Values), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1–2 hours. The build on this page has 11 steps.
No. This page has the complete, tested code (speech_timer_traffic_lights.ino). Install this library first: TM1637.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹403 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Active vs passive buzzers; Driving LEDs with resistors; Multiplexed 7-segment displays; Pull-ups and debouncing; Voltage dividers and analogRead().
Ideas that reuse this build: Stopwatch and Exam countdown display. They are listed under Take it further on this page.
Warm, cool, rainbow or breathing: cycle lighting moods from your sofa.
Press to roll: the pips tumble and slow down before landing on a number.
Wait for the light, hit the button: how many milliseconds can you beat?
A bright 4-digit clock that keeps time through power cuts.
Learning project. Check every circuit and the datasheet of each part before you power it up.
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.