LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsA magnet on the end of the steering shaft turns above the AS5600. The OLED shows the angle, so you can see how far the wheel is turned and tune the steering lock and gear ratio.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Measures the angle of a small magnet turning above the chip, to a resolution of 0.09 degrees, with no contact and no wear.
Follow the colours: red is power, dark grey is ground, blue is a signal.
steering_angle_meter.inoVerify & upload in Electrolark// Go-kart steering angle meter
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "steering-angle-meter"
#include <Wire.h>
#include "AS5600.h"
#include <Adafruit_GFX.h>
#include <Adafruit_SSD1306.h>
AS5600 as5600;
Adafruit_SSD1306 oled(128, 64, &Wire, -1);
// ---- latest readings ----
float angleDeg = 0;
const unsigned long READ_EVERY_MS = 100;
unsigned long lastRead = 0;
const char* statusText = "OK";
void updateDisplay() {
oled.clearDisplay();
oled.setTextSize(1);
oled.setCursor(0, 0);
oled.print(F("Steering"));
oled.drawLine(0, 10, 127, 10, SSD1306_WHITE);
oled.setCursor(0, 16);
oled.print(F("Angle"));
oled.setTextSize(2);
oled.setCursor(0, 28);
oled.print(angleDeg, 0);
oled.print(F(" deg"));
oled.setTextSize(1);
oled.display();
}
void setup() {
Serial.begin(115200);
Wire.begin();
as5600.begin();
if (!as5600.isConnected()) Serial.println(F("AS5600 not found"));
if (!oled.begin(SSD1306_SWITCHCAPVCC, 0x3C)) Serial.println(F("OLED not found"));
oled.setTextColor(SSD1306_WHITE);
oled.clearDisplay();
oled.display();
}
void loop() {
if (millis() - lastRead < READ_EVERY_MS) return;
lastRead = millis();
angleDeg = as5600.rawAngle() * 360.0f / 4096.0f;
Serial.print(F("Angle="));
Serial.print(angleDeg, 0);
Serial.print(F("deg"));
Serial.println();
updateDisplay();
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Check SDA and SCL. An I²C scanner should show 0x36.
Centre the magnet over the chip and keep the gap within 1 to 3 mm.
Check SDA/SCL and try address 0x3D. Run an I²C scanner to confirm.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
5 parts: Nano CH340 Development Board (Soldered), AS5600 Magnetic Encoder Sensor Module – 12-bit, I2C/PWM/Analog, 0.96" OLED Display 128x64 (I2C), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1 hour. The build on this page has 8 steps.
No. This page has the complete, tested code (steering_angle_meter.ino). Install these libraries first: AS5600, Adafruit SSD1306 and Adafruit GFX Library.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹563 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Drawing text on an I²C display; Magnetic encoders and rotary position.
Ideas that reuse this build: Valve and gate angle indicator and Window and door opening angle meter. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Angle=90deg Angle=90deg Angle=90deg Angle=90deg Angle=90deg Angle=90deg Angle=90deg Angle=90deg Angle=90deg
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.