LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsTwo sensors work together: a flame sensor pointed at the burner and a PIR that watches the kitchen. While someone is moving around the red light just shows that a flame is on; if the flame keeps burning and the PIR sees nobody for five minutes, the buzzer starts and keeps going until someone walks in.
A learning project, not a certified safety device. Never leave a flame unattended on purpose.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
Infrared photodiode tuned to 760–1100 nm, the light given off by flames, with a comparator for an on/off output.
Passive infrared sensor that detects the body heat of moving people or animals up to about 7 m away.
Active buzzer with a built-in oscillator: apply power and it beeps at about 2.3 kHz.
Follow the colours: red is power, dark grey is ground, blue is a signal.
stove_left_on_reminder.inoVerify & upload in Electrolark// Gas stove left-on reminder
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "stove-left-on-reminder"
// ---- pins ----
const uint8_t FLAME_PIN = 2;
const uint8_t PIR_PIN = 3;
const uint8_t BUZZER_PIN = 4;
const uint8_t LED_RED = 5;
// ---- latest readings ----
bool flame = false;
bool motion = false;
const unsigned long AWAY_MS = 5 * 60000UL; // Flame on with nobody around for this long
unsigned long lastPerson = 0;
bool alarm = false;
void setBuzzer(bool on) { digitalWrite(BUZZER_PIN, on ? HIGH : LOW); }
void setRedLed(bool on) { digitalWrite(LED_RED, on ? HIGH : LOW); }
void setup() {
Serial.begin(115200);
pinMode(FLAME_PIN, INPUT);
pinMode(PIR_PIN, INPUT);
pinMode(BUZZER_PIN, OUTPUT);
setBuzzer(false);
pinMode(LED_RED, OUTPUT);
lastPerson = millis();
setBuzzer(false);
}
void loop() {
flame = digitalRead(FLAME_PIN) == LOW;
motion = digitalRead(PIR_PIN) == HIGH;
if (motion) lastPerson = millis();
alarm = flame && millis() - lastPerson > AWAY_MS;
setRedLed(flame);
setBuzzer(alarm && (millis() / 300) % 2 == 0);
static unsigned long lastLog = 0;
if (millis() - lastLog > 2000) {
lastLog = millis();
Serial.print(flame ? F("Flame ON, ") : F("Flame off, ")); Serial.print((millis() - lastPerson) / 1000); Serial.println(F(" s since someone was seen"));
}
delay(20);
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Sunlight contains strong IR. Shade the sensor or lower the sensitivity with the trimmer.
Give it a minute to settle after power-up and keep it away from heaters, windows and fans.
Turn the sensitivity (Sx) pot clockwise and check the module has 5 V on VCC.
Low-triggered module: invert the logic in setBuzzer().
LED is reversed; flip it. Check the 220 Ω resistor is in series.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
9 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, Flame Sensor Module – LM393, Digital/Analog Output, HC-SR501 PIR Motion Detector Sensor Module, Active Buzzer Module 3.3–5V, Through-Hole LED Pack (Pack of 10), Resistor Assortment Kit (30 Values), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 1–2 hours. The build on this page has 11 steps.
No. This page has the complete, tested code (stove_left_on_reminder.ino).
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹496 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Active vs passive buzzers; Comparator outputs and sensitivity trimmers; Current-limiting resistors for LEDs; Digital inputs and sensor hold time.
A learning project, not a certified safety device. Never leave a flame unattended on purpose.
Ideas that reuse this build: LPG gas leak alarm and Flame detector fire alarm. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Flame off, 2 s since someone was seen
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.