LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsA borewell or sump pump that runs without water burns out in minutes. The waterproof ultrasonic sensor sits above the water, and when the surface is more than 140 cm below it, the buzzer and red LED warn you to switch the pump off. Pair it with a float or a pump controller for full protection.
This is an alert only and does not switch the pump. Anything connected to mains must be fitted by a qualified electrician.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
Waterproof ultrasonic probe on a 2.5 m cable.
Active buzzer with a built-in oscillator: apply power and it beeps at about 2.3 kHz.
Follow the colours: red is power, dark grey is ground, blue is a signal.
sump_dry_run_water_alarm.inoVerify & upload in Electrolark// Sump empty warning for the pump
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "sump-dry-run-water-alarm"
// ---- pins ----
const uint8_t TRIG_PIN = 2;
const uint8_t ECHO_PIN = 3;
const uint8_t BUZZER_PIN = 4;
const uint8_t LED_RED = 5;
// ---- latest readings ----
float distCm = 0;
const unsigned long READ_EVERY_MS = 1000;
unsigned long lastRead = 0;
bool alertOn = false;
const char* statusText = "Starting";
const float ALERT_LEVEL = 140; // a pump that runs dry overheats and its seals burn out
const float HYSTERESIS = 10; // gap that stops rapid on/off switching
float readDistanceCm() {
digitalWrite(TRIG_PIN, LOW);
delayMicroseconds(2);
digitalWrite(TRIG_PIN, HIGH);
delayMicroseconds(10);
digitalWrite(TRIG_PIN, LOW);
unsigned long us = pulseIn(ECHO_PIN, HIGH, 30000UL); // 30 ms timeout, about 5 m
if (us == 0) return -1; // no echo
return us * 0.0343f / 2.0f;
}
void setBuzzer(bool on) { digitalWrite(BUZZER_PIN, on ? HIGH : LOW); }
void setRedLed(bool on) { digitalWrite(LED_RED, on ? HIGH : LOW); }
void evaluate() {
if (!(distCm > 0)) { statusText = "Sensor error"; return; }
if (!alertOn && distCm > ALERT_LEVEL) alertOn = true;
else if (alertOn && distCm < ALERT_LEVEL - HYSTERESIS) alertOn = false;
statusText = alertOn ? "SUMP LOW" : "OK";
}
void setup() {
Serial.begin(115200);
pinMode(TRIG_PIN, OUTPUT);
pinMode(ECHO_PIN, INPUT);
pinMode(BUZZER_PIN, OUTPUT);
setBuzzer(false);
pinMode(LED_RED, OUTPUT);
}
void loop() {
if (millis() - lastRead >= READ_EVERY_MS) {
lastRead = millis();
distCm = readDistanceCm();
evaluate();
Serial.print(F("Distance="));
Serial.print(distCm, 0);
Serial.print(F("cm"));
Serial.print(F(", status=")); Serial.println(statusText);
}
setBuzzer(alertOn && (millis() / 250) % 2 == 0); // intermittent beep
setRedLed(alertOn && (millis() / 250) % 2 == 0);
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
TRIG and ECHO are swapped, or the sensor has no 5 V. Swap the two signal wires and check VCC.
Average several readings and keep wires short. Two HC-SR04s pinging at once will confuse each other.
Low-triggered module: invert the logic in setBuzzer().
LED is reversed; flip it. Check the 220 Ω resistor is in series.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
It stops the output flickering on and off when the reading hovers right at the limit. The output switches on at ALERT_LEVEL and only switches off once the reading has moved back by the hysteresis amount.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
8 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, JSN-SR04T-2.0 Waterproof Ultrasonic Sensor with 2.5m Probe, Active Buzzer Module 3.3–5V, Through-Hole LED Pack (Pack of 10), Resistor Assortment Kit (30 Values), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 2 hours. The build on this page has 9 steps.
No. This page has the complete, tested code (sump_dry_run_water_alarm.ino).
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹646 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Active vs passive buzzers; Current-limiting resistors for LEDs; Time-of-flight measurement with sound.
This is an alert only and does not switch the pump. Anything connected to mains must be fitted by a qualified electrician.
Ideas that reuse this build: Tank overflow alarm and Auto water tank pump. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Distance=60cm, status=OK Distance=60cm, status=OK
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.