LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsThe waterproof ultrasonic sensor measures the level from above, the float switch confirms the low mark, and the flow sensor shows the pump output. Together they tell you whether the pump is working.
Keep the board and display dry and away from the tank spill zone.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Waterproof ultrasonic probe on a 2.5 m cable.
A sealed float with a switch inside.
A small turbine with a magnet and Hall sensor: each turn sends a pulse, and pulses per second give the flow rate.
Follow the colours: red is power, dark grey is ground, blue is a signal.
tank_and_pump_status_board.inoVerify & upload in Electrolark// Tank and pump status board
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "tank-and-pump-status-board"
#include <Wire.h>
#include <Adafruit_GFX.h>
#include <Adafruit_SSD1306.h>
#if defined(ESP32) || defined(ESP8266)
#define IRAM_SAFE IRAM_ATTR
#else
#define IRAM_SAFE
#endif
// ---- pins ----
const uint8_t TRIG_PIN = 3;
const uint8_t ECHO_PIN = 4;
const uint8_t FLOAT_PIN = 5;
const uint8_t FLOW_PIN = 2;
volatile unsigned long flowPulses = 0;
unsigned long lastFlowMs = 0;
float litresTotal = 0;
Adafruit_SSD1306 oled(128, 64, &Wire, -1);
// ---- latest readings ----
float distCm = 0;
bool floatUp = false;
float flowLpm = 0;
float litres = 0;
const unsigned long READ_EVERY_MS = 1000;
unsigned long lastRead = 0;
const char* statusText = "OK";
float readDistanceCm() {
digitalWrite(TRIG_PIN, LOW);
delayMicroseconds(2);
digitalWrite(TRIG_PIN, HIGH);
delayMicroseconds(10);
digitalWrite(TRIG_PIN, LOW);
unsigned long us = pulseIn(ECHO_PIN, HIGH, 30000UL); // 30 ms timeout, about 5 m
if (us == 0) return -1; // no echo
return us * 0.0343f / 2.0f;
}
void IRAM_SAFE onFlowPulse() { flowPulses++; }
float readFlowLpm() {
unsigned long now = millis();
float secs = (now - lastFlowMs) / 1000.0f;
if (secs <= 0) return 0;
noInterrupts();
unsigned long p = flowPulses;
flowPulses = 0;
interrupts();
lastFlowMs = now;
float lpm = (p / secs) / 7.5f; // YF-S201: about 7.5 pulses per second per L/min
litresTotal += lpm * secs / 60.0f;
return lpm;
}
void updateDisplay() {
oled.clearDisplay();
oled.setTextSize(1);
oled.setCursor(0, 0);
oled.print(F("Tank"));
oled.drawLine(0, 10, 127, 10, SSD1306_WHITE);
oled.setCursor(0, 14);
oled.print(F("Distance: "));
oled.print(distCm, 0);
oled.print(F(" cm"));
oled.setCursor(0, 24);
oled.print(F("Float up: "));
oled.print(floatUp ? F("YES") : F("no"));
oled.setCursor(0, 34);
oled.print(F("Flow: "));
oled.print(flowLpm, 1);
oled.print(F(" L/min"));
oled.setCursor(0, 56);
oled.print(statusText);
oled.display();
}
void setup() {
Serial.begin(115200);
pinMode(TRIG_PIN, OUTPUT);
pinMode(ECHO_PIN, INPUT);
pinMode(FLOAT_PIN, INPUT_PULLUP);
pinMode(FLOW_PIN, INPUT_PULLUP);
attachInterrupt(digitalPinToInterrupt(FLOW_PIN), onFlowPulse, RISING);
lastFlowMs = millis();
if (!oled.begin(SSD1306_SWITCHCAPVCC, 0x3C)) Serial.println(F("OLED not found"));
oled.setTextColor(SSD1306_WHITE);
oled.clearDisplay();
oled.display();
}
void loop() {
if (millis() - lastRead < READ_EVERY_MS) return;
lastRead = millis();
distCm = readDistanceCm();
floatUp = digitalRead(FLOAT_PIN) == LOW;
flowLpm = readFlowLpm();
litres = litresTotal;
statusText = (distCm > 0) ? "OK" : "Sensor error";
Serial.print(F("Distance="));
Serial.print(distCm, 0);
Serial.print(F("cm"));
Serial.print(F(", Float up="));
Serial.print(floatUp ? F("yes") : F("no"));
Serial.print(F(", Flow="));
Serial.print(flowLpm, 1);
Serial.print(F("L/min"));
Serial.println();
updateDisplay();
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
TRIG and ECHO are swapped, or the sensor has no 5 V. Swap the two signal wires and check VCC.
Average several readings and keep wires short. Two HC-SR04s pinging at once will confuse each other.
Flip the float over (the arrow or marking points up) or swap the logic in the sketch.
Clear any dirt or sludge from around the float so it moves freely.
Check the arrow direction and that the signal wire is on an interrupt-capable pin.
Check SDA/SCL and try address 0x3D. Run an I²C scanner to confirm.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
7 parts: Nano CH340 Development Board (Soldered), JSN-SR04T-2.0 Waterproof Ultrasonic Sensor with 2.5m Probe, Square Float Switch, 2 m Cable, IP68 – Pump Tank Level Sensor, YF-S201 Water Flow Sensor 1–30 L/min, 0.96" OLED Display 128x64 (I2C), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 2–3 hours. The build on this page has 10 steps.
No. This page has the complete, tested code (tank_and_pump_status_board.ino). Install these libraries first: Adafruit SSD1306 and Adafruit GFX Library.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹1,094 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Drawing text on an I²C display; Interrupts and counting pulses; Level switches and pull-up resistors; Time-of-flight measurement with sound.
Keep the board and display dry and away from the tank spill zone.
Ideas that reuse this build: Pump house health logger and Wi-Fi sump and tank float monitor. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Distance=60cm, Float up=no, Flow=0.0L/min Distance=60cm, Float up=no, Flow=0.0L/min
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.