LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsReal weather stations measure rain with a tiny seesaw that tips each time it fills. A magnet on the seesaw passes the reed switch at every tip; the Nano counts them and shows the total in millimetres. Hold the button to reset after you write down the day's figure.
Tick anything you already have and the total updates.
Glass switch whose contacts close when a magnet is near.
Follow the colours: red is power, dark grey is ground, blue is a signal.
tipping_bucket_rain_gauge.inoVerify & upload in Electrolark// Tipping-bucket rain gauge
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "tipping-bucket-rain-gauge"
#include <Wire.h>
#include <Adafruit_GFX.h>
#include <Adafruit_SSD1306.h>
// ---- pins ----
const uint8_t REED_PIN = 2;
const uint8_t BUTTON_PIN = 3;
Adafruit_SSD1306 oled(128, 64, &Wire, -1);
// ---- latest readings ----
bool doorOpen = false;
const float MM_PER_TIP = 0.3; // calibrate: pour 100 ml through and count tips
unsigned long tips = 0, lastTip = 0;
bool wasClosed = false;
void show() {
oled.clearDisplay(); oled.setTextSize(1); oled.setCursor(0, 0); oled.print(F("Rainfall"));
oled.setTextSize(3); oled.setCursor(0, 14); oled.print(tips * MM_PER_TIP, 1);
oled.setTextSize(1); oled.setCursor(0, 42); oled.print(F("mm tips: ")); oled.print(tips);
oled.setCursor(0, 54); oled.print(F("Hold button to reset"));
oled.display();
}
void setup() {
Serial.begin(115200);
pinMode(REED_PIN, INPUT_PULLUP);
if (!oled.begin(SSD1306_SWITCHCAPVCC, 0x3C)) Serial.println(F("OLED not found"));
oled.setTextColor(SSD1306_WHITE);
oled.clearDisplay();
oled.display();
pinMode(BUTTON_PIN, INPUT_PULLUP);
show();
}
void loop() {
bool closed = digitalRead(REED_PIN) == LOW;
if (closed && !wasClosed && millis() - lastTip > 200) { tips++; lastTip = millis(); show(); Serial.println(tips * MM_PER_TIP, 1); }
wasClosed = closed;
if (digitalRead(BUTTON_PIN) == LOW) { delay(1000); if (digitalRead(BUTTON_PIN) == LOW) { tips = 0; show(); } }
delay(5);
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Bring the magnet within 1 cm and align it parallel to the glass body.
Check SDA/SCL and try address 0x3D. Run an I²C scanner to confirm.
The button is rotated 90°; legs on the same side are already connected. Turn it.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
6 parts: Nano CH340 Development Board (Soldered), Y213 Reed Switch Normally Open (glass), 0.96" OLED Display 128x64 (I2C), Tactile Push Button Switch, Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 2–3 hours. The build on this page has 9 steps.
No. This page has the complete, tested code (tipping_bucket_rain_gauge.ino). Install these libraries first: Adafruit SSD1306 and Adafruit GFX Library.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹449 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Drawing text on an I²C display; Pull-up resistors and reed switches; Pull-ups and debouncing.
Ideas that reuse this build: Rain alert and Weather logger. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.