Remote-controlled RGB mood light
Warm, cool, rainbow or breathing: cycle lighting moods from your sofa.
Shop by category
Shop all componentsOne infrared sensor at the start and one at the finish, both facing up under the track. The timer starts when a car passes the first and stops at the second, and the LCD shows the time and the best run. Great for Hot Wheels races and ramp experiments.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Two infrared reflectance sensors: black tape reflects little IR, white floor reflects a lot, so each output tells you which side the line is on.
Classic 16-character, 2-line LCD with an I²C backpack, so it needs only two signal wires.
Follow the colours: red is power, dark grey is ground, blue is a signal.
toy_car_race_timer.inoVerify & upload in Electrolark// Toy car race timer
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "toy-car-race-timer"
#include <Wire.h>
#include <LiquidCrystal_I2C.h>
// ---- pins ----
const uint8_t LINE_LEFT = 2;
const uint8_t LINE_RIGHT = 3;
LiquidCrystal_I2C lcd(0x27, 16, 2);
bool running = false, wasStart = false, wasFinish = false;
unsigned long startUs = 0, best = 0;
void setup() {
Serial.begin(115200);
pinMode(LINE_LEFT, INPUT);
pinMode(LINE_RIGHT, INPUT);
lcd.init();
lcd.backlight();
}
void loop() {
bool s = digitalRead(LINE_LEFT) == LOW, f = digitalRead(LINE_RIGHT) == LOW; // a car over each sensor
if (!running && s && !wasStart) { running = true; startUs = micros(); lcd.clear(); lcd.print(F("Running...")); }
if (running && f && !wasFinish) {
unsigned long t = (micros() - startUs) / 1000;
running = false;
if (!best || t < best) best = t;
lcd.clear(); lcd.print(F("Time ")); lcd.print(t / 1000.0, 3); lcd.print(F(" s"));
lcd.setCursor(0, 1); lcd.print(F("Best ")); lcd.print(best / 1000.0, 3); lcd.print(F(" s"));
Serial.println(t);
}
wasStart = s; wasFinish = f;
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Lower the sensor to 5–10 mm from the surface and re-tune the trimmer until its LED switches between the light and dark surface.
Adjust the contrast pot on the backpack. If still blank, change 0x27 to 0x3F.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
5 parts: Nano CH340 Development Board (Soldered), TCRT5000 Dual Channel Line Tracking Sensor Module, LCD1602 16x2 Character LCD (blue, with I2C adapter), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1–2 hours. The build on this page has 9 steps.
No. This page has the complete, tested code (toy_car_race_timer.ino). Install this library first: LiquidCrystal I2C.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹397 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Character displays and I²C backpacks; Infrared reflectance sensing.
Ideas that reuse this build: Ramp speed experiment and Stopwatch. They are listed under Take it further on this page.
Warm, cool, rainbow or breathing: cycle lighting moods from your sofa.
Press to roll: the pips tumble and slow down before landing on a number.
Wait for the light, hit the button: how many milliseconds can you beat?
A bright 4-digit clock that keeps time through power cuts.
Learning project. Check every circuit and the datasheet of each part before you power it up.
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.