LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsA heavy lopsided load can make a washing machine walk across the floor and damage the drum. The accelerometer is taped to the side panel and measures the shake. If it exceeds the limit during the spin, the buzzer tells you to pause and rearrange the clothes.
Keep the board dry and out of the splash zone, and never open the door during a spin.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Three-axis accelerometer that feels gravity and bumps, so it can measure tilt angles and detect knocks, drops and vibration.
Active buzzer with a built-in oscillator: apply power and it beeps at about 2.3 kHz.
Follow the colours: red is power, dark grey is ground, blue is a signal.
washing_machine_spin_shake_alarm.inoVerify & upload in Electrolark// Washing machine imbalance alarm
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "washing-machine-spin-shake-alarm"
#include <Wire.h>
#include <Adafruit_ADXL345_U.h>
#include <Adafruit_GFX.h>
#include <Adafruit_SSD1306.h>
// ---- pins ----
const uint8_t BUZZER_PIN = 2;
const uint8_t LED_RED = 3;
Adafruit_ADXL345_Unified accel = Adafruit_ADXL345_Unified(12345);
float adxX = 0, adxY = 0, adxZ = 1; // in g
Adafruit_SSD1306 oled(128, 64, &Wire, -1);
// ---- latest readings ----
float pitchDeg = 0;
float rollDeg = 0;
float shakeG = 0;
const unsigned long READ_EVERY_MS = 200;
unsigned long lastRead = 0;
bool alertOn = false;
const char* statusText = "Starting";
const float ALERT_LEVEL = 0.5; // about 0.5 g of extra shake is a violent spin; tune it on a normal load first
const float HYSTERESIS = 0.15; // gap that stops rapid on/off switching
void readAdxl() {
sensors_event_t e;
accel.getEvent(&e);
adxX = e.acceleration.x / 9.81f; adxY = e.acceleration.y / 9.81f; adxZ = e.acceleration.z / 9.81f;
}
float adxPitch() { return atan2(-adxX, sqrt(adxY * adxY + adxZ * adxZ)) * 57.3f; }
float adxRoll() { return atan2(adxY, adxZ) * 57.3f; }
float adxShake() { float m = sqrt(adxX * adxX + adxY * adxY + adxZ * adxZ); return fabs(m - 1.0f); }
void setBuzzer(bool on) { digitalWrite(BUZZER_PIN, on ? HIGH : LOW); }
void setRedLed(bool on) { digitalWrite(LED_RED, on ? HIGH : LOW); }
void updateDisplay() {
oled.clearDisplay();
oled.setTextSize(1);
oled.setCursor(0, 0);
oled.print(F("Spin shake"));
oled.drawLine(0, 10, 127, 10, SSD1306_WHITE);
oled.setCursor(0, 14);
oled.print(F("Pitch: "));
oled.print(pitchDeg, 1);
oled.print(F(" deg"));
oled.setCursor(0, 24);
oled.print(F("Roll: "));
oled.print(rollDeg, 1);
oled.print(F(" deg"));
oled.setCursor(0, 34);
oled.print(F("Shake: "));
oled.print(shakeG, 2);
oled.print(F(" g"));
oled.setCursor(0, 56);
oled.print(statusText);
oled.display();
}
void evaluate() {
if (!alertOn && shakeG > ALERT_LEVEL) alertOn = true;
else if (alertOn && shakeG < ALERT_LEVEL - HYSTERESIS) alertOn = false;
statusText = alertOn ? "UNBALANCED" : "Spin smooth";
}
void setup() {
Serial.begin(115200);
if (!accel.begin()) Serial.println(F("ADXL345 not found"));
accel.setRange(ADXL345_RANGE_4_G);
if (!oled.begin(SSD1306_SWITCHCAPVCC, 0x3C)) Serial.println(F("OLED not found"));
oled.setTextColor(SSD1306_WHITE);
oled.clearDisplay();
oled.display();
pinMode(BUZZER_PIN, OUTPUT);
setBuzzer(false);
pinMode(LED_RED, OUTPUT);
}
void loop() {
if (millis() - lastRead >= READ_EVERY_MS) {
lastRead = millis();
pitchDeg = (readAdxl(), adxPitch());
rollDeg = adxRoll();
shakeG = adxShake();
evaluate();
Serial.print(F("Pitch="));
Serial.print(pitchDeg, 1);
Serial.print(F("deg"));
Serial.print(F(", Roll="));
Serial.print(rollDeg, 1);
Serial.print(F("deg"));
Serial.print(F(", Shake="));
Serial.print(shakeG, 2);
Serial.print(F("g"));
Serial.print(F(", status=")); Serial.println(statusText);
updateDisplay();
}
setBuzzer(alertOn && (millis() / 250) % 2 == 0); // intermittent beep
setRedLed(alertOn && (millis() / 250) % 2 == 0);
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Check SDA and SCL. An I²C scanner should show 0x53 (0x1D if the ALT pin is high).
Keep the board still while it starts, and check pitch and roll are not swapped for your mounting.
Check SDA/SCL and try address 0x3D. Run an I²C scanner to confirm.
Low-triggered module: invert the logic in setBuzzer().
LED is reversed; flip it. Check the 220 Ω resistor is in series.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
It stops the output flickering on and off when the reading hovers right at the limit. The output switches on at ALERT_LEVEL and only switches off once the reading has moved back by the hysteresis amount.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
8 parts: Nano CH340 Development Board (Soldered), ADXL345 Digital Acceleration Sensor Module – I2C/SPI, 3.3V/5V, 0.96" OLED Display 128x64 (I2C), Active Buzzer Module 3.3–5V, Through-Hole LED Pack (Pack of 10), Resistor Assortment Kit (30 Values), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1 hour. The build on this page has 10 steps.
No. This page has the complete, tested code (washing_machine_spin_shake_alarm.ino). Install these libraries first: Adafruit ADXL345, Adafruit SSD1306 and Adafruit GFX Library.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹680 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Accelerometers, tilt angles and shock detection; Active vs passive buzzers; Current-limiting resistors for LEDs; Drawing text on an I²C display.
Keep the board dry and out of the splash zone, and never open the door during a spin.
Ideas that reuse this build: Ceiling fan wobble alarm and Machine vibration logger. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
0.0deg, Shake=0.00g, status=Spin smooth Pitch=0.0deg, Roll=0.0deg, Shake=0.00g, status=Spin smooth Pitch=0.0deg, Roll=0.0deg, Shake=0.00g, status=Spin smooth Pitch=0.0deg, Roll=0.0deg, Shake=0.00g, status=Spin smooth
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.