Buying guide · Beginner · 3 min read
3D Printer Cooling Fans
Part Cooling, Hotend and Mainboard Fans
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
A 3D printer has three fan jobs: the part cooling fan cools the print, the hotend fan keeps the cold end cool, and the mainboard fan cools the electronics. Replace fans with the same voltage, size and connector. The hotend fan must always run; if it fails, stop printing at once to avoid heat creep and clogs.
Key specs at a glance
- Part cooling fan
- Usually a 5015 blower on a duct, PWM controlled
- Hotend fan
- Often a 4010 axial fan, runs whenever the hotend is warm
- Mainboard fan
- Cools stepper drivers; may be thermostatic
- Voltage
- 12 V or 24 V; the supply must match
- Wires
- 2-wire (power) or 3-wire (with tachometer)
- Bearings
- Ball bearings last longer than sleeve bearings
What each fan does
blows air on the printed layer so plastic sets quickly. PLA needs strong cooling, ABS and ASA need little or none.
keeps the heatsink above the heat break cool. If it stops, filament softens too high in the tube and jams.
keeps drivers and the PSU cool; many run only when needed.
circulates or filters air on enclosed printers.
Blower or axial?
Blowers produce higher pressure through a duct and suit part cooling. Axial fans move more air in the open and suit heatsinks.
| Fan | Size | Use | Notes |
|---|---|---|---|
| Blower | 5015, 4020, 3010 | Part cooling through a duct | Good static pressure; direction matters |
| Axial | 4010, 4020, 6010 | Hotend heatsink, boards | Good airflow with open path |
| High-flow axial | 4020 or 4028 at 24 V | Fast cooling upgrades | Louder but stronger |
- Blower
- Size:
- 5015, 4020, 3010
- Use:
- Part cooling through a duct
- Notes:
- Good static pressure; direction matters
- Axial
- Size:
- 4010, 4020, 6010
- Use:
- Hotend heatsink, boards
- Notes:
- Good airflow with open path
- High-flow axial
- Size:
- 4020 or 4028 at 24 V
- Use:
- Fast cooling upgrades
- Notes:
- Louder but stronger
Replacing a fan
- 1Match voltage, size and connector. Putting a 12 V fan on 24 V burns it out.
- 2Check the airflow direction arrows on the fan body.
- 3Use the same duct or shroud so the air reaches the nozzle.
- 4For quieter prints, look for fans with PWM control and good bearings, or run the part fan below full speed.
- 5Some printers use special model fans for a toolhead; buy the one for your printer.
Common faults
dust or a worn bearing; clean it or replace.
loose connector, firmware fan setting or a dead fan.
set a lower maximum in the slicer.
clear the filament, replace the fan and check the heat break.
the part fan is too weak or the duct is blocked.
Try it: Pwm duty cycle calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Connecting a 12 V fan to a 24 V header.
- Printing with a dead hotend fan.
- Blocking the duct with debris or a bad zip tie.
- Mounting the fan with the airflow reversed.
- Using the part fan at full speed for ABS.
Frequently asked questions
Do I need to replace both fans together?
No. Replace the one that failed, but check the other for noise and dust.
What does the 3-pin connector do?
The third wire reports speed (tach) to the board so it can detect a stall.
Can a bigger fan help?
A stronger fan or duct can improve overhangs, but it needs the right mount and more power.
How do I quieten my printer?
Use quality bearings, lower the fan speed, add rubber mounts and replace worn fans.
Why does the hotend fan run all the time?
By design. It must cool the heatsink whenever the hotend is warm.
Parts for this guide
Calculators
Terms in this guide
Projects that use it
Put this into practice: 1 step-by-step build in our project library uses parts from this guide.
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.




