Buying guide · Beginner · 4 min read
PLA and PLA+ Filament
Which to Buy, Print Settings and Storage
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
PLA is the easiest 3D printing filament: it prints at 190 to 220 degrees C, barely warps and needs no enclosure. PLA+ is a modified blend that is tougher and less brittle, usually printing 5 to 15 degrees hotter. Both soften at about 55 to 60 degrees C, so keep them away from hot cars. Buy 1.75 mm filament on a 1 kg spool unless your printer says otherwise.
Key specs at a glance
- Diameter
- 1.75 mm for almost all desktop printers (2.85 mm only on a few older machines)
- Nozzle temperature
- PLA 190 to 220 °C; PLA+ and high-speed PLA 205 to 235 °C
- Bed temperature
- 0 to 65 °C (a textured PEI plate can print PLA cold)
- Part cooling fan
- 100% after the first layer
- Heat limit
- Softens around 55 to 60 °C
- Length on a 1 kg spool
- About 335 m of 1.75 mm filament
- Diameter tolerance
- ±0.02 to ±0.03 mm on decent filament
What PLA is and why it is the default
PLA (polylactic acid) is a plastic made from fermented plant starch. It melts at a low temperature, shrinks very little as it cools and does not release strong fumes, which is why it is the first filament almost everyone prints. It makes sharp detail, glossy or matte surfaces and a huge range of colours.
Its weaknesses are heat and impact. A PLA part left on a car dashboard will sag, and a thin PLA clip will snap rather than bend. If a part will be hot, stressed or outdoors, look at PETG or ABS and ASA instead.
PLA, PLA+, high-speed, matte and silk compared
Brands use different names, so read the product label. These are the common families:
| Type | What changes | Good for | Watch out for |
|---|---|---|---|
| Standard PLA | Plain polylactic acid | Test prints, display models, cheap prototypes | Brittle in thin parts |
| PLA+ / Tough PLA | Blended with impact modifiers | Brackets, enclosures, functional parts | Needs 5 to 15 °C more heat; blends vary by brand |
| High-speed PLA (PLA-HS) | Flows better at high volumetric speed | Fast printers that run 300 mm/s or more | Slow printers gain little from it |
| Matte PLA | Filler gives a low-gloss finish | Hiding layer lines, cosplay, decor | Slightly weaker layers than plain PLA |
| Silk PLA | Shiny, metallic look | Vases, trophies, decorative prints | Weaker layers; keep it for looks, not load |
| PLA-CF (carbon fibre) | Chopped fibre for stiffness | Rigid jigs and drone frames | Abrasive: use a hardened steel nozzle |
- Standard PLA
- What changes:
- Plain polylactic acid
- Good for:
- Test prints, display models, cheap prototypes
- Watch out for:
- Brittle in thin parts
- PLA+ / Tough PLA
- What changes:
- Blended with impact modifiers
- Good for:
- Brackets, enclosures, functional parts
- Watch out for:
- Needs 5 to 15 °C more heat; blends vary by brand
- High-speed PLA (PLA-HS)
- What changes:
- Flows better at high volumetric speed
- Good for:
- Fast printers that run 300 mm/s or more
- Watch out for:
- Slow printers gain little from it
- Matte PLA
- What changes:
- Filler gives a low-gloss finish
- Good for:
- Hiding layer lines, cosplay, decor
- Watch out for:
- Slightly weaker layers than plain PLA
- Silk PLA
- What changes:
- Shiny, metallic look
- Good for:
- Vases, trophies, decorative prints
- Watch out for:
- Weaker layers; keep it for looks, not load
- PLA-CF (carbon fibre)
- What changes:
- Chopped fibre for stiffness
- Good for:
- Rigid jigs and drone frames
- Watch out for:
- Abrasive: use a hardened steel nozzle
Starting print settings
Use the temperature range printed on the spool as your starting point and adjust from there. If the label gives no range, try these:
| Setting | PLA | PLA+ / high-speed |
|---|---|---|
| Nozzle | 200 to 215 °C | 215 to 230 °C |
| Bed | 55 to 60 °C | 55 to 65 °C |
| Fan | 100% | 100% |
| Retraction (direct drive) | 0.5 to 1 mm | 0.5 to 1 mm |
| Speed | 40 to 80 mm/s | Up to the printer's limit |
- Nozzle
- PLA:
- 200 to 215 °C
- PLA+ / high-speed:
- 215 to 230 °C
- Bed
- PLA:
- 55 to 60 °C
- PLA+ / high-speed:
- 55 to 65 °C
- Fan
- PLA:
- 100%
- PLA+ / high-speed:
- 100%
- Retraction (direct drive)
- PLA:
- 0.5 to 1 mm
- PLA+ / high-speed:
- 0.5 to 1 mm
- Speed
- PLA:
- 40 to 80 mm/s
- PLA+ / high-speed:
- Up to the printer's limit
What to check before you buy
Match your printer (1.75 mm for nearly all). A tolerance of ±0.03 mm or better avoids under-extrusion.
Refills come without a spool and cost less, but you need a reusable spool or a printer that takes spool-less rolls.
1 kg spools are standard; 250 g and 500 g spools are handy for trying colours, 2 kg and 5 kg suit print farms.
Dark colours print a little differently from light ones; white and natural often show more layer lines.
Multi-material systems and some printers prefer their own spool size, so check the spool diameter and hole before buying.
Keeping PLA dry
PLA absorbs moisture from the air. Wet filament pops and crackles at the nozzle, leaves tiny bubbles and strings badly. Store opened spools in a sealed box with desiccant. To dry a damp spool, hold it at 45 to 50 °C for 4 to 6 hours in a filament dryer; never go much above 55 °C or the spool softens and deforms.
Try it: Filament length calculator
Change the values and the diagram and results update as you type.
Print your first PLA part
You need: 1.75 mm PLA filament, Clean build plate · Tools: 3D printer, Slicer, Flush cutters
Get the parts2 of 2 found in our store · ₹1,923
1.75 mm PLA filamentAnycubic PLA Filament 1kg 1.75mm₹944Closest match, check the specs
Clean build plateELEGOO Mars 4 build plate₹979Closest match, check the specs
- 1Dry and loadCheck the spool is dry, feed the filament into the extruder and purge until the colour runs clean.
- 2Set temperaturesPick a PLA profile at 205 °C nozzle and 60 °C bed, with the part fan at 100% after layer 1.
- 3Level and printRun bed levelling, then print a 20 mm calibration cube and watch the first layer.
- 4AdjustIf corners lift, clean the plate with isopropyl alcohol. If you see strings, lower the nozzle by 5 °C or dry the spool.
Common mistakes to avoid
- Printing PLA+ at plain-PLA temperatures and getting weak, matte-looking layers.
- Leaving a spool open for weeks in a humid room.
- Using PLA for parts that sit in a hot car or near a motor.
- Printing carbon-fibre PLA through a brass nozzle, which wears out in hours.
- Buying a spool-less refill without a spool to hold it.
Frequently asked questions
Is PLA+ really stronger than PLA?
Usually yes. PLA+ blends add impact modifiers, so it bends a little before it breaks. The exact recipe differs by brand, so strength claims are not standardised.
Can PLA go outdoors?
Short term, yes, but sunlight heats parts past 60 °C and they sag. For outdoor parts use ASA or PETG.
Is PLA food safe?
The plastic itself is food-grade, but printed parts have tiny gaps that trap bacteria and some brass nozzles contain traces of lead, so do not use PLA prints for repeated food contact.
Why does my PLA string?
Common causes are wet filament, a nozzle that is too hot and retraction that is too low. Dry the spool first.
Do I need a heated bed for PLA?
It helps. A bed at 55 to 60 °C improves first-layer grip, though a textured PEI plate can hold PLA cold.
How long does a 1 kg spool last?
A 1 kg spool holds about 335 m of 1.75 mm PLA, enough for roughly 30 to 60 hours of typical printing.
Parts for this guide
Calculators
Terms in this guide
Projects that use it
Put this into practice: 1 step-by-step build in our project library uses parts from this guide.
Keep learning
Sources
- Polymaker and eSUN published PLA and PLA+ datasheets
- NatureWorks Ingeo 4043D technical datasheet
- Prusa Knowledge Base: PLA
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.




