Buying guide · Beginner · 3 min read
PETG Filament
Settings, Stringing Fixes and When to Choose It
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
PETG is a tough, slightly flexible filament that resists water, chemicals and about 70 to 75 degrees C of heat, so it suits functional parts better than PLA. It prints at 230 to 250 degrees C on a 70 to 85 degrees C bed with low fan. Expect some stringing, and never print it directly on bare glass without a release agent, because it can bond and chip the glass.
Key specs at a glance
- Nozzle temperature
- 230 to 250 °C
- Bed temperature
- 70 to 85 °C
- Part cooling fan
- 20 to 50%
- Heat limit
- About 70 to 75 °C before softening
- Enclosure
- Not required
- Shrinkage
- Very low, so it warps much less than ABS
- Drying
- 60 to 65 °C for 6 to 8 hours
What makes PETG different
PETG is PET, the plastic in drink bottles, with glycol added so it prints without turning cloudy. Compared with PLA it bends before it breaks, handles heat better, shrugs off water and many chemicals, and bonds well between layers. Compared with ABS it needs no enclosure, smells less and warps less.
The trade-off is a stickier melt. PETG strings, leaves blobs and sticks very hard to smooth surfaces, so settings matter more than with PLA.
PETG compared with PLA and ABS
How the three most common functional filaments compare:
| Property | PLA | PETG | ABS / ASA |
|---|---|---|---|
| Ease of printing | Easiest | Moderate | Hard, needs enclosure |
| Heat resistance | 55 to 60 °C | 70 to 75 °C | 90 to 100 °C |
| Impact toughness | Low | Good | Good |
| Layer bonding | Fair | Excellent | Good when hot |
| UV outdoors | Poor | Fair | ASA is best |
| Stringing | Low | High | Low |
- Ease of printing
- PLA:
- Easiest
- PETG:
- Moderate
- ABS / ASA:
- Hard, needs enclosure
- Heat resistance
- PLA:
- 55 to 60 °C
- PETG:
- 70 to 75 °C
- ABS / ASA:
- 90 to 100 °C
- Impact toughness
- PLA:
- Low
- PETG:
- Good
- ABS / ASA:
- Good
- Layer bonding
- PLA:
- Fair
- PETG:
- Excellent
- ABS / ASA:
- Good when hot
- UV outdoors
- PLA:
- Poor
- PETG:
- Fair
- ABS / ASA:
- ASA is best
- Stringing
- PLA:
- Low
- PETG:
- High
- ABS / ASA:
- Low
Settings that work
Go lower on the first layer if it squashes too flat.
, and 0% for the first few layers. Full fan weakens the layer bond.
40 to 60 mm/s gives clean surfaces; high-speed PETG blends handle more.
on the first layer (about 0.05 mm extra Z offset). PETG sticks too well if squashed.
a little longer than for PLA, and enable wipe and z-hop to cut strings and blobs.
PETG can fuse with it. A thin coat of glue stick works as a release layer, or print on a textured sheet.
Good uses for PETG
PETG suits brackets, drone and robot parts, water-contact parts, clear covers, snap-fit clips and enclosures for sensors. It is not stiff enough for precision gears, and it is a poor choice for fine detail where stringing would show.
Drying and storage
PETG takes up moisture quickly. Wet PETG gives hissing, rough surfaces and heavy strings. Dry at 60 to 65 °C for 6 to 8 hours and store in a sealed box with desiccant. See filament drying and storage.
Try it: Filament length calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Running the part fan at 100% and losing layer strength.
- Printing the first layer too close to the plate so PETG welds itself to the sheet.
- Skipping drying and blaming the printer for strings.
- Printing on bare glass or smooth PEI without a release layer.
- Expecting PETG to be stiffer than PLA; it is tougher, not stiffer.
Frequently asked questions
Is PETG stronger than PLA?
It is tougher and holds up better to impacts, drops and heat, but PLA is stiffer and feels more rigid in thin walls.
Why is my PETG stringing?
Usually from wet filament or a nozzle that is too hot. Dry the spool and try lowering the nozzle by 5 °C.
Can I print PETG on a smooth PEI plate?
Yes, but use a thin layer of glue stick or a textured plate, because PETG can bond so hard that it pulls pieces off the sheet.
Is PETG food safe?
The raw resin is food-contact grade, but 3D printed layers hold bacteria. Treat prints as single-use for food.
Does PETG need an enclosure?
No. It prints fine in open air, although drafts can weaken layers.
Is PETG waterproof?
Printed parts resist water well if walls are thick and fully sealed, but they are not guaranteed leak-proof.
Parts for this guide
Calculators
Terms in this guide
Projects that use it
Put this into practice: 1 step-by-step build in our project library uses parts from this guide.
Keep learning
Sources
- Eastman Eastar PETG datasheet
- eSUN and Polymaker PETG technical data sheets
- Prusa Knowledge Base: PETG
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.




